SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2005MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)BODY & FRAMEWINDOWSWINDSHIELD/WINDOWGLASS/MIRRORPOWER MIRROR CONTROL SYSTEMINSPECTION
2005 Toyota Matrix XR, FWD, Standard

Power Mirror Control System: Inspection

2005 Toyota Matrix XR, FWD, StandardSECTION Inspection
  1. INSPECT OUTER MIRROR SWITCH ASSY 
    1. Left side for left/right adjustment switch:

      Measure the resistance of the mirror switch.

      TESTER CONNECTION AND SPECIFIED CONDITION (1 OF 2)

      Tester Connection Switch Condition Specified Condition
      - OFF 10 kΩ or higher
      4-8
      6-7 UP Below 1 Ω
      4-7
      6-8 DOWN Below 1 Ω
      5-8
      6-7 LEFT Below 1Ω
      5-7
      6-8 RIGHT Below 1 Ω

      If the result is not as specified, replace the switch assembly.

    2. Right side for left/right adjustment switch:

      Measure the resistance of the mirror switch.

      Fig 1: Measuring Resistance Of Mirror Switch
      G02635659Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TESTER CONNECTION AND SPECIFIED CONDITION (2 OF 2)

      Tester Connection Switch Condition Specified Condition
      - OFF 10 kΩ or higher
      3-8 UP Below 1 Ω
      6-7
      3-7 DOWN Below 1Ω
      6-8
      2-8 LEFT Below 1Ω
      6-7
      2-7 RIGHT Below 1Ω
      6-8

      If the result is not as specified, replace the switch assembly.

  2. INSPECT OUTER REAR VIEW MIRROR ASSY LH 
    1. Disconnect the outer rear view mirror assembly LH connector.
    2. Apply battery voltage and inspect the mirror motor face operation.
      MEASUREMENT CONDITION AND SPECIFIED CONDITION (1 OF 2)

      Measurement Condition Specified Condition
      Battery positive (+) - MV (3) Turns upward (A)
      Battery negative (-) - Com (2)
      Battery positive (+) - Com (2) Turns downward (B)
      Battery negative (-) - MV (3)
      Battery positive (+) - Com (2) Turns left (C)
      Battery negative (-) - MH (1)
      Battery positive (+)-MH(1) Turns right (D)
      Battery negative (-) - Com (2)

      If the result is not as specified, replace the mirror assembly.

      Fig 2: Identifying Outer Rear View Mirror Assembly LH Connector
      G02635660Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSPECT OUTER REAR VIEW MIRROR ASSY RH 
    1. Disconnect the outer rear view mirror assembly RH connector.
    2. Apply battery voltage and inspect the mirror motor face operation.
      MEASUREMENT CONDITION AND SPECIFIED CONDITION (2 OF 2)

      Measurement Condition Specified Condition
      Battery positive (+) - MV (3) Turns upward (A)
      Battery negative (-) - Com (2)
      Battery positive (+) - Com (2) Turns downward (B)
      Battery negative (-) - MV (5)
      Battery positive (+) - Com (2) Turns right (D)
      Battery negative (-) - MH (1)
      Battery positive (+)-MH(1) Turns left (C)
      Battery negative (-) - Com (2)

      If the result is not as specified, replace the mirror assembly.

      Fig 3: Identifying Outer Rear View Mirror Assembly RH Connector
      G02635661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.