2005 Toyota Land CruiserFACTORY OEM SERVICE PROCEDURE

On-Vehicle Inspection

NOTE: "Cold" and "Hot" in these sentences express the temperature of the coils themselves. "Cold" is from -10°C (14°F) to 50°C (122°F) and "Hot" is from 50°C (122°F) to 100°C (212°F).
  1. INSPECT IGNITION COIL (WITH IGNITER) AND SPARK TEST 

    Check that the spark occurs.

    1. Remove the ignition coils (with igniter) (See REMOVAL  ).
    2. Remove the spark plugs.
    3. Install the spark plugs to each ignition coil (with igniter), and connect the ignition coil (with igniter) connector.
    4. Disconnect the 8 injector connectors.
    5. Ground the spark plug.
    6. Check if spark occurs while engine is being cranked.
      NOTE: To prevent gasoline from being injected from injectors during this test, crank the engine for no more than 5 - 10 seconds at time.

      If the spark does not occur, do the test as follows:

      Fig 1: No-Spark Test Flow Chart
      G03076589Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Using a 16 mm plug wrench, install the spark plugs.

      Torque: 17.5 N.m (180 kgf.cm, 13 ft.lbf) 

    8. Reinstall the ignition coils (with igniter) (See REMOVAL  ).
  2. INSPECT SPARK PLUGS 
    NOTE:
    • Never use a wire brush for cleaning.
    • Never attempt to adjust the electrode gap on used spark plug.
    • Spark plug should be replaced every 100,000 km (60,000 miles).
    1. Remove the ignition coils (with igniter) (See REMOVAL  ).
    2. Check the electrode.
      • Using a megger (insulation resistance meter), measure the insulation resistance.

        Correct insulation resistance: 10 MΩ or more 

        Fig 2: Checking Insulation Resistance
        G03076590Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the resistance is less than specified, proceed to step  d.

      HINT:

      If a megger is not available, the following simple method of inspection provides fairly accurate results.

      • Simple Method:
        • Quickly race the engine to 4,000 rpm 5 times.
        • Remove the spark plug. (See step  c)
        • Visually check the spark plug.

          If the electrode is dry ... OK.

          If the electrode is wet ... Proceed to step  d.

        • Reinstall the spark plug. (See step  g)
          Fig 3: Inspecting Spark Plug Electrode
          G03076591Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a 16 mm plug wrench, remove the spark plugs.
      Fig 4: Removing Spark Plugs
      G03076592Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Check the spark plug for thread damage and insulator damage.

      If abnormal, replace the spark plug.

      RECOMMENDED SPARK PLUG

      DENSO made SK20R11
      NGK made IFR6A11
      Fig 5: Checking Spark Plug For Thread Damage & Insulator Damage
      G03076593Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Check the spark plug electrode gap.

      Maximum electrode gap for used spark plug: 

      1.3 mm (0.051 in.) 

      If the gap is greater than maximum, replace the spark plug.

      Correct electrode gap for new spark plug: 

      1.1 mm (0.043 in.) 

      NOTE: If adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap on a used plug.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.