Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2004 Toyota Land CruiserFACTORY OEM SERVICE PROCEDURE
Service Data
Service Data Table - Automatic Transmission
| A750F | ||
| Line pressure (Wheel locked) | ||
| Engine idling | ||
| D position | 362 - 420 kPa (3.7 - 4.3 kgf.cm2 , 53 - 61 psi) | |
| R position | 500 - 580 kPa (5.1 - 5.9 kgf.cm2 , 73 - 84 psi) | |
| AT stall (Throttle valve fully opened) | ||
| D position | 1,360 - 1,460 kPa (13.9 - 14.9 kgf.cm2 , 197 - 212 psi) | |
| R position | 1,295 - 1,415 kPa (13.2 - 14.4 kgf.cm2 , 188 - 205 psi) | |
| Engine stall revolution | D and R positions | 2,150 ± 150 rpm |
| Time lag | N → D position | Less than 1.2 seconds |
| N → R position | Less than 1.5 seconds | |
| Engine idle speed | ||
| (A/C OFF) | N position | 700 ± 50 rpm |
| Drive plate runout | Max. | 0.20 mm (0.0079 in.) |
| Torque converter runout | Max. | 0.30 mm (0.0118 in.) |
| Torque converter clutch installation distance | More than 17.1 mm (0.673 in.) | |
| Shift schedule | ||
| D position | ||
| (Throttle valve fully opened) | 1 → 2 | 45 - 57 km/h (28 - 35 mph) |
| 2 → 3 | 79 - 90 km/h (49 - 56 mph) | |
| 3 → 4 | 113 - 128 km/h (70 - 80 mph) | |
| 4 → 5 | 165 - 180 km/h (103 - 112 mph) | |
| 5 → 4 | 158 - 173 km/h (98 - 108 mph) | |
| 4 → 3 | 105 - 117 km/h (65 - 73 mph) | |
| 3 → 2 | 70 - 78 km/h (43 - 48 mph) | |
| 2 → 1 | 35 - 41 km/h (22 - 25 mph) | |
| (Throttle valve fully closed) | 4 → 5 | 32 - 38 km/h (20 - 24 mph) |
| 5 → 4 | 24 - 29 km/h (15 - 18 mph) | |
| 3 position | ||
| (Throttle valve fully opened) | 1 → 2 | 45 - 57 km/h (28 - 35 mph) |
| 2 → 3 | 79 - 90 km/h (49 - 56 mph) | |
| 4 → 3 | 119 - 132 km/h (74 - 82 mph) | |
| 3 → 2 | 70 - 78 km/h (43 - 48 mph) | |
| 2 → 1 | 35 - 41 km/h (22 - 25 mph) | |
| 2 position | ||
| (Throttle valve fully opened) | 1 → 2 | 45 - 57 km/h (28 - 35 mph) |
| 3 → 2 | 80 - 88 km/h (50 - 55 mph) | |
| 2 → 1 | 35 - 41 km/h (22 - 25 mph) | |
| L position | ||
| (Throttle valve fully opened) | 2 → 1 | 41 - 47 km/h (25 - 29 mph) |
| Lock-up point | Throttle valve opening 5 % | |
| D position | ||
| 5th gear | Lock-up ON | 67 - 74 km/h (42 - 46 mph) |
| Lock-up OFF | 60 - 67 km/h (37 - 42 mph) | |
| 4 position | ||
| 4th gear | Lock-up ON | 61 - 68 km/h (38 - 42 mph) |
| Lock-up OFF | 54 - 61 km/h (34 - 38 mph) | |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.