Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Toyota Matrix Base, 4WDFACTORY OEM SERVICE PROCEDURE
Service Data
Lubrication System Service Specifications (1ZZ-FE)
| Oil pressure | at idle speed | 29 kPa (0.3 kgf.cm2 , 4.2 psi) or more |
| at 3,000 r/min | 294 - 539 kPa (3.0 - 5.5 kgf.cm2 , 43 - 78 psi) or more | |
| Adhesive | Part No. 08833 - 00080, THREE BOND 1344, LOCTITE 242, or equivalent | |
| Engine oil | ||
| Capacity | Drain and refill w/ oil filter change | 3.7 liters (3.9 US qts, 3.3 lmp. qts) |
| Drain and refill w/o oil filter change | 3.5 liters (3.7 US qts, 3.1 lmp. qts) | |
| Dry fill | 4.2 liters (4.4 US qts, 3.7 lmp. qts) | |
| Oil pump assy | ||
| Tip clearance | 0.040 - 0.160 mm (0.0016 - 0.0063 in.) | |
| Body clearance | 0.260 - 0.325 mm (0.0102 - 0.0128 in.) | |
| Side clearance | 0.025 - 0.071 mm (0.0010 - 0.0028 in.) | |
Lubrication System Service Specifications (2ZZ-GE)
| Oil pressure | ||
| at idle speed | 19.2 kPa (0.2 kgf.cm2 , 2.8 psi) or more | |
| at 3,000 r/min | 294 - 539 kPa (3.0 - 5.5 kgf.cm2 , 43 - 78 psi) or more | |
| Adhesive | Part No. 08833 - 00080, THREE BOND 1344, LOCTITE 242, or equivalent | |
| Engine oil | ||
| Capacity | Drain and refill w/ oil filter change | 4.4 liters (4.7 US qts, 3.9 lmp. qts) |
| Drain and refill w/o oil filter change | 4.2 liters (4.4 US qts, 3.7 lmp. qts) | |
| Dry fill | 4.8 liters (5.1 US qts, 4.2 lmp. qts) | |
| Oil pump assy | ||
| Tip clearance | Standard | 0.060 - 0.180 mm (0.0024 - 0.0071 in.) |
| Maximum | 0.35 mm (0.0138 in.) | |
| Body clearance | Standard | 0.125 - 0.180 mm (0.0049 - 0.0071 in.) |
| Maximum | 0.325 mm (0.0128 in.) | |
| Side clearance | Standard | 0.030 - 0.080 mm (0.0012 - 0.0032 in.) |
| Maximum | 0.16 mm (0.0063 in.) | |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
