Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Toyota Highlander Base, 3.0 F, AWDFACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code Definitions
DIAGNOSTIC TROUBLE CODE DEFINITIONS
| DTC (1) 0 |
Description | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| B2796 (2)(3) | No Communication In Immobilizer System | ||||||||
| B2797 (2)(3) | Communication Malfunction No. 1 | ||||||||
| B2798 (2)(3) | Communication Malfunction No. 2 | ||||||||
| P0010 | Camshaft Position "A" Actuator Circuit (Bank No. 1) | ||||||||
| P0011 | Camshaft Position "A" - Timing Over - Advanced Or System Performance (Bank No. 1) | ||||||||
| P0012 | Camshaft Position "A" - Timing Over - Retarded (Bank No. 1) | ||||||||
| P0016 | Crankshaft Position - Camshaft Position Correlation (Bank No. 1 Sensor "A") | ||||||||
| P0018 | Crankshaft Position - Camshaft Position Correlation (Bank No. 2 Sensor "A") | ||||||||
| P0020 | Camshaft Position "A" Actuator Circuit (Bank No. 2) | ||||||||
| P0021 | Camshaft Position "A" - Timing Over - Advanced Or System Performance (Bank No. 2) | ||||||||
| P0022 | Camshaft Position "A" - Timing Over - Retarded (Bank No. 2) | ||||||||
| P0036 | Oxygen Sensor Heater Control Circuit (Bank No. 1 Sensor No. 2) | ||||||||
| P0100 (4) | Mass Air Flow Circuit Malfunction | ||||||||
| P0101 | Mass Air Flow Circuit Range/Performance Problem | ||||||||
| P0110 (4) | Intake Air Temperature Circuit Malfunction | ||||||||
| P0115 (4) | Engine Coolant Temperature Circuit Malfunction | ||||||||
| P0116 | Engine Coolant Temperature Circuit Range/Performance Problem | ||||||||
| P0120 (4) | Throttle/Pedal Position Sensor/Switch "A" Circuit Malfunction | ||||||||
| P0121 | Throttle/Pedal Position Sensor/Switch "A" Circuit Range/Performance Problem | ||||||||
| P0125 | Insufficient Coolant Temperature For Closed Loop Fuel Control | ||||||||
| P0128 | Thermostat Malfunction | ||||||||
| P0134 | Oxygen Sensor Circuit No Activity Detected (Bank No. 1 Sensor No. 1) | ||||||||
| P0135 (4) | Oxygen Sensor Heater Circuit (Bank No. 1 Sensor No. 1) | ||||||||
| P0136 | Oxygen Sensor Circuit Malfunction (Bank No. 1 Sensor No. 2) | ||||||||
| P0154 | Oxygen Sensor Circuit No Activity Detected (Bank No. 2 Sensor No. 1) | ||||||||
| P0155 (4) | Oxygen Sensor Heater Circuit (Bank No. 2 Sensor No. 1) | ||||||||
| P0171 | System Too Lean (Fuel Trim, Bank No. 1) | ||||||||
| P0172 | System Too Rich (Fuel Trim, Bank No. 1) | ||||||||
| P0174 | System Too Lean (Bank No. 2) | ||||||||
| P0175 | System Too Lean (Bank No. 2) | ||||||||
| P0300 | Random/Multiple Cylinder Misfire Detected | ||||||||
| P0301 | Cylinder No. 1 Misfire Detected | ||||||||
| P0302 | Cylinder No. 2 Misfire Detected | ||||||||
| P0303 | Cylinder No. 3 Misfire Detected | ||||||||
| P0304 | Cylinder No. 4 Misfire Detected | ||||||||
| P0305 | Cylinder No. 5 Misfire Detected | ||||||||
| P0306 | Cylinder No. 6 Misfire Detected | ||||||||
| P0325 (4) | Knock Sensor No. 1 Circuit Malfunction (Bank No. 1 Or Single Sensor) | ||||||||
| P0330 (4) | Knock Sensor No. 2 Circuit Malfunction (Bank No. 2) | ||||||||
| P0335 | Crankshaft Position Sensor "A" Circuit Malfunction | ||||||||
| P0339 (3) | Crankshaft Position Sensor "A" Circuit Intermittent | ||||||||
| P0340 | Camshaft Position Sensor Circuit Malfunction | ||||||||
| P0341 | Camshaft Position Sensor "A" Circuit Range/Performance (Bank No. 1 Or Single Sensor) | ||||||||
| P0345 | Camshaft Position Sensor "A" Circuit (Bank No. 2) | ||||||||
| P0346 | Camshaft Position Sensor "A" Circuit Range/Performance (Bank No. 2) | ||||||||
| P0351 (4) | Ignition Coil "A" Primary/Secondary Circuit | ||||||||
| P0352 (4) | Ignition Coil "B" Primary/Secondary Circuit | ||||||||
| P0353 (4) | Ignition Coil "C" Primary/Secondary Circuit | ||||||||
| P0354 (4) | Ignition Coil "D" Primary/Secondary Circuit | ||||||||
| P0355 (4) | Ignition Coil "E" Primary/Secondary Circuit | ||||||||
| P0356 (4) | Ignition Coil "F" Primary/Secondary Circuit | ||||||||
| P0420 | Catalyst System Efficiency Below Threshold (Bank No. 1) | ||||||||
| P0441 | EVAP System Incorrect Purge Flow | ||||||||
| P0442 | EVAP System Leak Detected (Small Leak) | ||||||||
| P0446 | EVAP System Vent Control Malfunction | ||||||||
| P0450 | EVAP System Pressure Sensor Malfunction | ||||||||
| P0451 | EVAP System Pressure Sensor Range/Performance | ||||||||
| P0456 | EVAP System Leak Detected (Very Small Leak) | ||||||||
| P0500 | Vehicle Speed Sensor Malfunction | ||||||||
| P0505 | Idle Control System Malfunction | ||||||||
| P0511 | Idle Air Control Circuit | ||||||||
| P0513 (2)(3) | Incorrect Immobilizer Key | ||||||||
| P0560 | System Voltage | ||||||||
| P0724 | Brake Switch "B" Circuit High | ||||||||
| P0850 | Park/Neutral Position Switch Malfunction | ||||||||
| P1645 | Body ECU Malfunction | ||||||||
| P2195 | Oxygen Sensor Signal Stuck Lean (Bank No. 1 Sensor No. 1) | ||||||||
| P2196 | Oxygen Sensor Signal Stuck Rich (Bank No. 1 Sensor No. 1) | ||||||||
| P2197 | Oxygen Sensor Signal Stuck Lean (Bank No. 2 Sensor No. 1) | ||||||||
| P2198 | Oxygen Sensor Signal Stuck Rich (Bank No. 2 Sensor No. 1) | ||||||||
| P2237 | Oxygen Sensor Pumping Current Circuit/Open For A/F Sensor (Bank No. 1 Sensor No. 1) | ||||||||
| P2240 | Oxygen Sensor Pumping Current Circuit/Open For A/F Sensor (Bank No. 2 Sensor No. 1) | ||||||||
| P2A00 | A/F Sensor Circuit Slow Response (Bank No. 1 Sensor No. 1) | ||||||||
| P2A03 | A/F Sensor Circuit Slow Response (Bank No. 2 Sensor No. 1) | ||||||||
|
|||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
