Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2001 Toyota 4Runner BaseFACTORY OEM SERVICE PROCEDURE
Fluid Capacities (Highlander)
FLUID CAPACITIES (HIGHLANDER)
| Application | (1) Quantity | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Automatic Transaxle (Toyota Type "T-IV" ATF) | |||||||||
| 2WD | |||||||||
| 2.4L 4-Cyl. | |||||||||
| Drain & Refill | 3.5 Qts. (3.3L) | ||||||||
| Dry Refill | |||||||||
| With Air Cooled Oil Cooler | 9.5 Qts. (9.0L) | ||||||||
| Without Air Cooled Oil Cooler | 9.1 Qts. (8.6L) | ||||||||
| 3.0 V6 | |||||||||
| Drain & Refill | 3.3 Qts. (3.1L) | ||||||||
| Dry Refill | |||||||||
| With Air Cooled Oil Cooler | 9.3 Qts. (8.8L) | ||||||||
| Without Air Cooled Oil Cooler | 8.9 Qts. (8.4L) | ||||||||
| 4WD | |||||||||
| Drain & Refill | 4.1 Qts. (3.9L) | ||||||||
| Dry Refill | |||||||||
| With Air Cooled Oil Cooler | 9.2 Qts. (8.7L) | ||||||||
| Without Air Cooled Oil Cooler | 8.8 Qts. (8.3L) | ||||||||
| Cooling System (Includes Heater) | |||||||||
| 2.4L 4-Cyl. | 6.8 Qts. (6.4L) | ||||||||
| 3.0L V6 | 9.9 Qts. (9.4L) | ||||||||
| Crankcase (Includes Filter) (2) | |||||||||
| 2.4L 4-Cyl. | 4.0 Qts. (3.8L) | ||||||||
| 3.0L V6 | 5.0 Qts. (4.7L) | ||||||||
| Differential (SAE 80W-90/API GL-5) | |||||||||
| 4WD | |||||||||
| Rear Axle | 1.0 Qt. (.9L) | ||||||||
| Power Steering Fluid (Dexron-III) | |||||||||
| 2.4L 4-Cyl. | |||||||||
| With Towing Package | 1.0 Qt. (.9L) | ||||||||
| Without Towing Package | .85 Qt. (.80L) | ||||||||
| 3.0L V6 | .85 Qt. (.80L) | ||||||||
| Transfer Case (SAE 80W-90/API GL-5) | 1.0 Qt. (.9L) | ||||||||
|
|||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
