2000 Toyota RAV4 Base, AWD, StandardFACTORY OEM SERVICE PROCEDURE

Vehicle Engine/VIN Id: Notes

2000 MODEL COVERAGE

MODEL ENGINE ENGINE ID (1) FUEL SYSTEM (2) IGNITION SYSTEM
Avalon 3.0L V6 (1MZ-FE) F SFI DIS (3)
Camry 2.2L 4-Cyl. (5S-FE) (4) G SFI DIS (3)
2.2L 4-Cyl. (5S-FNE) (5) N SFI DIS (3)
3.0L V6 (1MZ-FE) F SFI DIS (3)
Camry Solara 2.2L 4-Cyl. (5S-FE) G SFI DIS (3)
3.0L V6 (1MZ-FE) F SFI DIS (3)
Celica 1.8L 4-Cyl. (1ZZ-FE) R SFI DIS (3)
1.8L 4-Cyl. (2ZZ-GE) Y SFI DIS (3)
Corolla 1.8L 4-Cyl. (1ZZ-FE) R SFI DIS (3)
ECHO 1.5L 4-Cyl. (1NZ-FE) T SFI DIS (3)
Land Cruiser 4.7L V8 (2UZ-FE) T SFI DIS (3)
RAV4 2.0L 4-Cyl. (3S-FE) P SFI DIS (3)
Sienna 3.0L V6 (1MZ-FE) F SFI DIS (3)
Tacoma 2.4L 4-Cyl. (2RZ-FE) L SFI DIS (3)
2.7L 4-Cyl. (3RZ-FE) M SFI DIS (3)
3.4L V6 (5VZ-FE) N SFI DIS (3)
Tundra 3.4L V6 (5VZ-FE) N SFI DIS (3)
4.7L V8 (2UZ-FE) T SFI DIS (3)
4Runner 2.7L 4-Cyl. (3RZ-FE) M SFI DIS (3)
3.4L V6 (5VZ-FE) N SFI DIS (3)
(1) Engine may be identified by Vehicle Identification Number (VIN). Vin is located on VIN plate on left side of instrument panel. See Figure-Figure . Engine serial number is stamped on cylinder block. See Figure-Figure .
(2) Fuel injection system is a Sequential Multiport Fuel Injection (SFI) system.
(3) Application uses a Distributorless Ignition System (DIS).
(4) This is the gasoline engine application.
(5) This is the Compressed Natural Gas (CNG) engine application.
Fig 1: VIN Definition
G00011329Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Chapter Navigation
Return to Chapter: Vehicle Engine/VIN Id
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.