2000 Toyota MR2FACTORY OEM SERVICE PROCEDURE

Section 375 (Defogger System): Inspection

WARNING: This page is about a different car, the 2004 Toyota MR2. However, it is still accessible from the selected car via links, so may be relevant.
  1. Inspect Defogger Timer Operation 
    1. Connect the positive (+) lead from the battery to terminal 1 and negative (-) lead to terminal 4.
      Fig 1: Inspecting Defogger Timer Operation
      G02911789Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive (+) lead from the battery to terminal 12 through a 3.4 W test bulb.
    3. Turn the defogger switch ON and check that the indicator light and test bulb light up for 12 for 18 minutes, then the indicator light and test bulb lights go out.

      If the operation is not as specified, replace the switch.

  2. Connector Disconnected: Inspect Defogger Switch Circuit 

    Disconnect the connector from the switch and inspect the connector on the wire harness side, as shown in the chart.

    Fig 2: Identifying Defogger Switch Connector Terminals
    G02911790Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    DEFOGGER SWITCH SPECIFICATIONS

    Tester connection Condition Specified condition
    12 - Ground Constant Continuity
    4 - Ground Ignition switch LOCK or ACC No voltage
    4 - Ground Ignition switch ON Battery positive voltage

    If the circuit is as specified, replace the switch.

  3. Connector Connected: Inspect Defogger Switch Circuit 

    Connect the connector to the switch and inspect the wire harness side connector from the back side, as shown in the chart.

    Fig 3: Identifying Defogger Switch Connector Terminals
    G02911791Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    TESTER CONNECTION SPECIFIED CONDITION

    Tester connection Condition Specified condition
    4 - Ground Ignition switch ON and defogger switch OFF Battery positive voltage
    4 - Ground Ignition switch ON and defogger switch ON No voltage

    If the circuit is as specified, try replacing the switch with a new one.

    If the circuit is not as specified, inspect the circuit connected to other parts.

  4. Inspect Defogger Relay Continuity 
    Fig 4: Identifying Defogger Relay Terminals
    G02911792Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    TESTER CONNECTOR SPECIFIED CONDITION

    Condition Tester connection Specified condition
    Constant 1 - 2 Continuity
    Apply B+ between terminals 1 and 2. 3 - 5 Continuity

    If the continuity is not as specified, replace the relay.

  5. Inspect Defogger Wire 
    NOTE:
    • When cleaning the glass, use a soft, dry cloth, and wipe the glass in the direction of the wire. Take care not to damage the wires.
    • Do not use detergents or glass cleaners with abrasive ingredients.
    • When measuring voltage, wind a piece of tin foil around the top of the negative probe and press the foil against the wire with your finger, as shown.
      Fig 5: Identifying Tester Probe
      G02911793Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Turn the ignition switch ON.
      Fig 6: Checking Voltage At Center Of Wire
      G02911794Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the defogger switch ON.
    3. Inspect the voltage at the center of each heat wire, as shown.
      VOLTAGE CRITERIA

      Voltage Results
      Approx. 5 V Okay (No break in wire)
      Approx. 10 V or 0 V Broken wire
      Fig 7: Checking Broken Wire Voltage
      G02911795Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.