Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Toyota MR2FACTORY OEM SERVICE PROCEDURE
Difficult To Start
Difficult To Start & Engine Cranks Normally
- On Avalon, Camry, Camry Solara, Corolla, Highlander, Land Cruiser, MR2, RAV4, Sequoia, Sienna, Tacoma, Tundra and 4Runner, check starter signal circuit. See STARTER SIGNAL CIRCUIT under COMPUTERIZED ENGINE CONTROLS in appropriate SYSTEM & COMPONENT TESTING article.
- On Celica and ECHO, check starter signal circuit at STA terminal on Engine Control Module (ECM). See WIRING DIAGRAMS article. For illustration of ECM location, see THEORY & OPERATION article. No other testing information is available from manufacturer.
- On Avalon, Camry 2.2L 4-cylinder gasoline models, Camry 3.0L V6, Camry Solara, Celica, Corolla, ECHO, Highlander, MR2, Prius, RAV4, Sienna, Tacoma, Tundra 3.4L V6 and 4Runner, check fuel pump control circuit. See FUEL PUMP CONTROL CIRCUIT under COMPUTERIZED ENGINE CONTROLS in appropriate SYSTEM & COMPONENT TESTING article.
- On Camry 2.2L 4-cylinder CNG models, check fuel shutoff valve circuit. See DTC P1190: FUEL SHUTOFF VALVE MALFUNCTION test in SELF-DIAGNOSTICS - CAMRY 4-CYLINDER - CNG article.
- On Land Cruiser, check fuel pump control circuit. See DTC P1200: FUEL PUMP RELAY/ECU CIRCUIT test in SELF-DIAGNOSTICS - LAND CRUISER article.
- On 2001 MR2 with sequential manual transaxle, check throttle body and components for Electronic Throttle Control System (ETCS). See THROTTLE BODY under IDLE CONTROL SYSTEMS in SYSTEM & COMPONENT TESTING - 4-CYLINDER article. Models with sequential manual transaxle may be identified by the shift lever pattern which consists of "R", "N", "S" and "+" in place of the conventional type shift lever pattern and no clutch pedal is used.
- On Sequoia and Tundra 4.7L V8, check fuel pump control circuit. See DTC P1200: FUEL PUMP RELAY CIRCUIT test in appropriate SELF-DIAGNOSTICS article.
- On all models, check engine compression. See MECHANICAL INSPECTION under PRELIMINARY INSPECTION & ADJUSTMENTS in appropriate BASIC DIAGNOSTIC PROCEDURES article.
Difficult To Start When Engine Is Hot Or Cold
- On Avalon, Camry, Camry Solara, Corolla, Highlander, Land Cruiser, MR2, RAV4, Sequoia, Sienna, Tacoma, Tundra and 4Runner, check starter signal circuit. See STARTER SIGNAL CIRCUIT under COMPUTERIZED ENGINE CONTROLS in appropriate SYSTEM & COMPONENT TESTING article.
- On Celica and ECHO, check starter signal circuit at STA terminal on Engine Control Module (ECM). See WIRING DIAGRAMS article. For illustration of ECM location, see THEORY & OPERATION article. No other testing information is available from manufacturer.
- On Avalon, Camry 2.2L 4-cylinder gasoline models, Camry 3.0L V6, Camry Solara, Celica, Corolla, ECHO, Highlander, MR2, Prius, RAV4, Sienna, Tacoma, Tundra 3.4L V6 and 4Runner, check fuel pump control circuit. See FUEL PUMP CONTROL CIRCUIT under COMPUTERIZED ENGINE CONTROLS in appropriate SYSTEM & COMPONENT TESTING article.
- On Camry 2.2L 4-cylinder CNG models, check fuel shutoff valve circuit. See DTC P1190: FUEL SHUTOFF VALVE MALFUNCTION test in SELF-DIAGNOSTICS - CAMRY 4-CYLINDER - CNG article.
- On Land Cruiser, check fuel pump control circuit. See DTC P1200: FUEL PUMP RELAY/ECU CIRCUIT test in SELF-DIAGNOSTICS - LAND CRUISER article.
- On 2001 MR2 with sequential manual transaxle, check throttle body and components for Electronic Throttle Control System (ETCS). See THROTTLE BODY under IDLE CONTROL SYSTEMS in SYSTEM & COMPONENT TESTING - 4-CYLINDER article. Models with sequential manual transaxle may be identified by the shift lever pattern which consists of "R", "N", "S" and "+" in place of the conventional type shift lever pattern and no clutch pedal is used.
- On Sequoia and Tundra 4.7L V8, check fuel pump control circuit. See DTC P1200: FUEL PUMP RELAY CIRCUIT test in appropriate SELF-DIAGNOSTICS article.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
