Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1998 Toyota 4Runner Base, 4WD, StandardFACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code Definitions
DIAGNOSTIC TROUBLE CODE (DTC) DEFINITIONS
| DTC | Description | ||||
|---|---|---|---|---|---|
| P0100 (1) | Mass Airflow (MAF) Sensor Circuit | ||||
| P0101 (1) | Mass Airflow (MAF) Circuit Range/Performance Problem | ||||
| P0110 | Intake Air Temperature (IAT) Sensor Circuit | ||||
| P0115 | Engine Coolant Temperature (ECT) Sensor Circuit | ||||
| P0116 (1) | Engine Coolant Temperature (ECT) Sensor Circuit Range/Performance Problem | ||||
| P0120 | Throttle Position (TP) Sensor Circuit Malfunction | ||||
| P0121 (1) | Throttle Position (TP) Sensor Circuit Range/Performance Problem | ||||
| P0125 | Insufficient Coolant Temperature For Closed Loop Fuel Control | ||||
| P0130 (1) | (2) Heated Oxygen Sensor Circuit (Sensor No. 1) | ||||
| P0133 (1) | (2) Heated Oxygen Sensor Circuit (Sensor No. 1) Slow Response | ||||
| P0135 (1) | Heated Oxygen Sensor Circuit | ||||
| P0136 (1) | (2) Heated Oxygen Sensor Circuit (Sensor No. 2) | ||||
| P0141 (1) | Heated Oxygen Sensor Circuit | ||||
| P0171 (1) | System Too Lean (Fuel Trim) | ||||
| P0172 (1) | System Too Rich (Fuel Trim) | ||||
| P0300 | Random Misfire Detected | ||||
| P0301 (1) | Cylinder No. 1 Misfire Detected | ||||
| P0302 (1) | Cylinder No. 2 Misfire Detected | ||||
| P0303 (1) | Cylinder No. 3 Misfire Detected | ||||
| P0304 (1) | Cylinder No. 4 Misfire Detected | ||||
| P0325 | Knock Sensor Circuit | ||||
| P0335 (1) | Crankshaft Position (CKP) Sensor Circuit | ||||
| P0340 (1) | Camshaft Position (CMP) Sensor Circuit | ||||
| P0401 (1) | Insufficient Exhaust Gas Recirculation (EGR) Flow Detected | ||||
| P0402 (1) | Excessive Exhaust Gas Recirculation (EGR) Flow Detected | ||||
| P0420 (1) | Catalyst System Efficiency Below Threshold | ||||
| P0440 (1) | Evaporative Emission Control System Malfunction | ||||
| P0441 (1) | Incorrect EVAP Purge Flow | ||||
| P0446 (1) | EVAP Vent Control Malfunction | ||||
| P0450 | EVAP Pressure Sensor Fault | ||||
| P0451 | EVAP Pressure Sensor Range/Performance | ||||
| P0500 (1) | Vehicle Speed Sensor Fault | ||||
| P0505 (1) | Idle Air Control (IAC) System Malfunction | ||||
| P1300 | Ignitor Circuit No. 1 Fault | ||||
| P1310 | Ignitor Circuit No. 2 Fault | ||||
| P1335 | Crankshaft Position (CKP) Sensor Circuit | ||||
| P1520 (1) | Stoplight Switch Signal Malfunction (A/T Only) | ||||
| P1600 | ECM BATT Malfunction | ||||
| P1780 (1) | Park/Neutral Position (PNP) Switch | ||||
|
|||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
