Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1995 Toyota Tercel Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Engine Controls - Tests W/Codes
- Introduction
- Self-Diagnostic System
- Testing & Repair Procedure
- Scan Tester Problems
- Component Location
- Summary
- Diagnostic Testing
- Notes
- Code P0105 - Manifold Absolute Pressure/Barometric Pressure (Map) Sensor Circuit
- Code P0106 - Manifold Absolute Pressure/Barometric Pressure (Map) Circuit Range/Performance Problem
- Code P0110 - Intake Air Temperature (IAT) Sensor Circuit
- Code P0115 - Coolant Temperature Sensor (Cts) Circuit
- Code P0116 - Coolant Temperature Sensor (Cts) Circuit Range/Performance Problem
- Code P0120 - Throttle Position Sensor (TPS) Circuit Malfunction
- Code P0121 - Throttle Position Sensor (TPS) Circuit Range/Performance Problem
- Code P0125 - Insufficient Coolant Temperature For Closed Loop Fuel Control
- Code P0130 - Heated Oxygen Sensor (Front Sensor) Circuit
- Code P0133 - Heated Oxygen Sensor (Front Sensor) Circuit Slow Response
- Code P0135 - Heated Oxygen Sensor (Front Sensor) Circuit
- Code P0136 - Heated Oxygen Sensor (Rear Sensor) Circuit
- Code P0141 - Heated Oxygen Sensor (Rear Sensor) Circuit
- Code P0170 - Fuel Trim Malfunction
- Code P0300 - Random/Multiple Misfire Detected
- Codes P0301-P0304 - Cylinders No. 1-4 Misfire Detected
- Code P0325 - Knock Sensor No. 1 Circuit
- Code P0335 - Crankshaft Position (CKP) Sensor "A" Circuit
- Code P0340 - Camshaft Position (CMP) Sensor Circuit
- Code P0401 - Insufficient Exhaust Gas RECIRCULATION (EGR) Flow Detected
- Code P0402 - Excessive Exhaust Gas RECIRCULATION (EGR) Flow Detected
- Code P0420 - Catalyst System Efficiency Below Threshold
- Code P0500 - Vehicle Speed Sensor Malfunction
- Code P0505 - Idle Control System Malfunction
- Code P0510 - Closed Throttle Position Switch Malfunction
- Code P1300 - IGNITOR Circuit Malfunction
- Code P1335 - Crankshaft Position (CKP) Sensor Circuit Malfunction During Engine Operation
- Code P1500 - Starter Signal Circuit Malfunction
- Code P1600 - ECM Batt Malfunction
- Code P1605 - Knock Control CPU Malfunction
- Code P1780 - Park/Neutral Position (PNP) Switch
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.