1995 Toyota Pickup BaseFACTORY OEM SERVICE PROCEDURE

General Specifications & VIN Identification

1995 MODEL COVERAGE

Model Body Engine EngineID (1) Fuel System(2) Ignition System
Avalon MCX 3.0L V6 (1MZ-FE) G SFI (3) DIS
Camry SXV 2.2L 4-Cyl. (5S-FE) S (4) Magnetic
MCV 3.0L V6 (1MZ-FE) G SFI (3) DIS
Celica AT 1.8L 4-Cyl. (7A-FE) A MFI Magnetic
ST 2.2L 4-Cyl. (5S-FE) S (4) Magnetic
Corolla AE 1.6L 4-Cyl. (4A-FE) A MFI Magnetic
AE 1.8L 4-Cyl. (7A-FE) A SFI Magnetic
Land Cruiser FZJ 4.5L 6-Cyl. (1FZ-FE) D SFI Magnetic
MR2 SW 2.0L 4-Cyl. (3S-GTE) (5) S SFI Magnetic
SW 2.2L 4-Cyl. (5S-FE) (6) S MFI Magnetic
Paseo EL 1.5L 4-Cyl. (5E-FE) E MFI (7)
Pickup RN 2.4L 4-Cyl. (22R-E) R MFI Magnetic
VZN 3.0L V6 (3VZ-E) V MFI Magnetic
Previa TCR 2.4L 4-Cyl. (2TZ-FE) (8) A MFI Magnetic
TCR 2.4L 4-Cyl. (2TZ-FZE) (9) A MFI Magnetic
Supra JZA 3.0L 6-Cyl. (2JZ-GE) (6) J SFI Magnetic
JZA 3.0L 6-Cyl. (2JZ-GTE) (5) J SFI (3) DIS
Tacoma RZN 2.4L 4-Cyl. (2RZ-FE) U MFI Magnetic
RZN 2.7L 4-Cyl. (3RZ-FE) U MFI Magnetic
VZN 3.4L V6 (5VZ-FE) V SFI (3) DIS
Tercel EL 1.5L 4-Cyl. (5E-FE) E MFI (3) DIS
T100 RCK 2.7L 4-Cyl. (3RZ-FE) U MFI Magnetic
VCK 3.4L V6 (5VZ-FE) V SFI (3) DIS
4Runner RN 2.4L 4-Cyl. (22R-E) R MFI Magnetic
VZN 3.0L V6 (3VZ-E) V MFI Magnetic
(1) Engine may be identified by Vehicle Identification Number (VIN) or number stamped on engine block. See Figure and Figure. VIN is located on stamped plate on left side of instrument panel.
(2) Fuel injection system may be a Sequential Multiport Fuel Injection (SFI) system or a Multiport Fuel Injection (MFI) system. Note application listed for fuel system ID.
(3) Application uses a Distributorless Ignition System (DIS).
(4) On Calif. emission vehicles, a Sequential Multiport Fuel Injection (SFI) system is used. On all other models, a Multiport Fuel Injection (MFI) system is used.
(5) This is the turbo engine.
(6) This is the non-turbo engine.
(7) On Calif. emission vehicles, a Distributorless Ign. System (DIS) is used. On all other models, a magnetic ign. system is used.
(8) This is the non-supercharged engine.
(9) This is the supercharged engine.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.