1994 Toyota Tercel BaseFACTORY OEM SERVICE PROCEDURE

Valve Clearance: PASEO

  1. Remove valve cover(s) and gasket(s). Rotate crankshaft so timing mark on crankshaft pulley aligns with "0" mark on front cover and cylinder No. 1 (front cylinder at timing belt or timing chain end) is at TDC on compression stroke.
  2. Ensure valves on cylinder No. 1 are closed. If valves are not closed, rotate crankshaft 360 degrees (one full revolution). With cylinder No. 1 at TDC, check valve clearance on specified valves. See the VALVE CLEARANCE ADJUSTMENT SEQUENCE  table. See Fig 1.
    Fig 1: Typical 4-Cylinder Valve Arrangement (Camry, Celica, Corolla, Paseo, Previa & T100)
    G94F44235Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. Using feeler gauge, measure and record valve clearance between valve lifter and camshaft. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS  table.
  4. To check remaining valves, rotate crankshaft 360 degrees (one full revolution) until cylinder No. 4 is at TDC on compression stroke. Measure valve clearance on specified valves. See appropriate VALVE CLEARANCE ADJUSTMENT SEQUENCE  table.
  5. If valve clearance requires adjustment, rotate crankshaft so camshaft lobe on valve to be adjusted is facing upward, away from valve lifter. Rotate valve lifter so notch on valve lifter is toward spark plug.
  6. Valve Clearance Adjuster (SST 09248-55040) is used for adjusting valve clearance. Press valve lifter downward using SST "A" of valve clearance adjuster. See Fig 2. Install SST "B" between camshaft and valve lifter. Remove SST "A". Shim thickness can also be determined by using the following formula: N = T + A.
    • N = Thickness of adjuster shim required.
    • T = Thickness of adjuster shim removed.
    • A = Measured clearance minus valve clearance specification.
  7. Using small screwdriver and magnet, remove adjusting shim. Using micrometer, measure thickness of adjusting shim removed. Using measured clearance and adjusting shim thickness, determine correct thickness of adjusting shim to be used. See SHIM THICKNESS  table. Install adjusting shim. Recheck valve clearance.
    NOTE: Before installing valve cover gasket, apply sealant at camshaft bearing caps-to-cylinder head surfaces where valve cover gasket seals.
  8. Install valve cover using NEW gasket. On Previa, remove bolt from accessory drive shaft. Reverse removal procedure to install remaining components.
Fig 2: Removing & Installing Valve Clearance Adjusting Shim
G94G44236Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
VALVE CLEARANCE ADJUSTMENT SEQUENCE

Piston No. On TDC Adjust Intake Valves Adjust Exhaust Valves
1 1 & 2 1 & 3
4 3 & 4 2 & 4
VALVE CLEARANCE SPECIFICATIONS

Application (1) In. (mm)
Paseo
Exhaust .012-.016 (.30-.41)
Intake .006-.010 (.15-.25)
Tercel (Exhaust & Intake) .008 (.20)
(1) On Tercel, adjust valve clearance with engine at normal operating temperature. On Paseo, adjust valve clearance with engine cold.
SHIM THICKNESS

Thickness mm (in.) Shim No.
2.50 (0.0984) 1
2.55 (0.1004) 2
2.60 (0.1024) 3
2.65 (0.1043) 4
2.70 (0.1063) 5
2.75 (0.1083) 6
2.80 (0.1102) 7
2.85 (0.1122) 8
2.90 (0.1142) 9
2.95 (0.1161) 10
3.00 (0.1181) 11
3.05 (0.1201) 12
3.10 (0.1220) 13
3.15 (0.1240) 14
3.20 (0.1260) 15
3.25 (0.1280) 16
3.30 (0.1299) 17
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.