Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1990 Toyota Celica All-TracFACTORY OEM SERVICE PROCEDURE
External Pages
These are pages that do not belong to the exact selected vehicle (1990 Toyota Celica All-Trac), but are still accessible from a link in your vehicle's manual. Be very cautious using repair info from here because these pages may not apply to your vehicle.
- Different car
- Section 1 (Specifications - 4-CYL)
- Section 2 (Specifications - V6)
- Section 3 (Adjustments - 4-CYL EFI)
- Section 4 (Adjustments - 6-CYL)
- Section 5 (Adjustments - V6)
- Section 6 (Basic Testing - 4-CYL EFI)
- Section 7 (Basic Testing - 6-CYL)
- Section 8 (Basic Testing - V6)
- Section 9 (Engine Controls - Tests W/Codes - EFI)
- Section 10 (Tests W/Codes)
- Section 11 (Engine Controls - Tests W/Codes - EFI)
- Section 12 (Engine Controls - Tests W/Codes - EFI)
- Section 13 (Engine Controls - Tests W/Codes - EFI)
- Section 14 (Tests W/Codes - EFI)
- Section 15 (Engine Controls - System/Component Tests - EFI)
- Section 16 (Engine Controls - System/Component Tests - EFI)
- Section 17 (Specifications - 6-CYL)
- Section 18 (Engine Controls - Specifications - 6-CYL)
- Section 19 (Engine Controls - Specifications - V6)
- Section 20 (Engine Controls - Adjustments - V6 EFI)
- Section 21 (Engine Controls - Tests W/Codes)
- Section 22 (Engine Controls - Tests W/Codes - 4-CYL EFI)
- Section 23 (Engine Controls - Tests W/Codes - 4-CYL EFI)
- Section 24 (Engine Controls - Tests W/Codes - V6)
- Section 25 (Engine Controls - Tests W/Codes - EFI)
- Section 26 (Engine Controls - System/Component Tests - EFI)
- Section 27 (Pin Voltage Charts)
- Section 28 (Engine Controls - Pin Voltage Charts)
- Section 29 (Engine Controls - Tests W/O Codes - 4-CYL EFI)
- Section 30 (Wiring Diagrams - 4-CYL (EFI))
- Section 31 (Engine Controls - System/Component Tests - 4-CYL EFI)
- Section 32 (Engine Controls - Pin Voltage Charts - 4-CYL EFI)
- Section 33 (Engine Controls - Tests W/O Codes - 4-CYL EFI)
- Section 34 (Wiring Diagrams - 4-CYL (EFI))
- Section 35 (Pin Voltage Charts - 4-CYL EFI)
- Section 36 (Engine Controls - System/Component Tests - 4-CYL EFI)
- Section 37 (Axle Shafts - Front)
- Section 38 (Wheel Alignment Specifications & Procedures)
- Section 39 (Wheel Alignment Specifications & Procedures)
- Section 40 (Wheel Alignment Specifications & Procedures)
- Section 41 (Wheel Alignment Specifications & Procedures)
- Section 42 (Wheel Alignment Specifications & Procedures)
- Section 43 (Overhaul - A-241E/H/L & A-243E)
- Section 44 (Removal & Installation - M/T)
- Section 45 (Removal & Installation - M/T)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
