Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2010 Suzuki Equator 2WD L4-2.5LFACTORY OEM SERVICE PROCEDURE
System Specifications
Cylinder Head Bolts
Whenever the size difference between (d1) and (d2) exceeds the limit, replace them with a new one.

Limit [(d1) (d2)]: 0.23 mm (0.0091 in)
If reduction of outer diameter appears in a position other than (d2), use it as (d2) point.

Step a 50 Nm (5.1 kg-m, 37 ft-lb)
Step b 60 degrees clockwise
Step c Loosen to 0 Nm in the reverse order of tightening.
Step d 39.2 Nm (4.0 kg-m, 29 ft-lb)
Step e 75 degrees clockwise
Step f 75 degrees clockwise
Cylinder Head Distortion
Limit 0.1 mm (0.004 in)
Intake manifold

Intake manifold bolts 9.4 Nm (0.96 kg-m, 83 in-lb)
No. 6 means double tightening of bolt No. 1
Camshaft brackets

Step 1 (bolts 9 - 11) 2.0 Nm (0.2 kg-m, 17 in-lb)
Step 2 (bolts 1 - 8) 2.0 Nm (0.2 kg-m, 17 in-lb)
Step 3 (bolts 1 - 11) 5.9 Nm (0.6 kg-m, 52 in-lb)
Step 4 (bolts 1 - 11) 10.4 Nm (1.1 kg-m, 92 in-lb)
Camshaft sprocket (INT) 103 Nm (11 kgf-m, 76 ft lb)
Camshaft sprocket (EXH) 142 Nm (14 kgf-m, 105 ft lb)
Exhaust manifold 41.7 Nm (4.3 kgf-m, 31 ft lb)

Tighten nuts in numerical order as shown again
Whenever the size difference between (d1) and (d2) exceeds the limit, replace them with a new one.
Limit [(d1) (d2)]: 0.23 mm (0.0091 in)
If reduction of outer diameter appears in a position other than (d2), use it as (d2) point.
Step a 50 Nm (5.1 kg-m, 37 ft-lb)
Step b 60 degrees clockwise
Step c Loosen to 0 Nm in the reverse order of tightening.
Step d 39.2 Nm (4.0 kg-m, 29 ft-lb)
Step e 75 degrees clockwise
Step f 75 degrees clockwise
Cylinder Head Distortion
Limit 0.1 mm (0.004 in)
Intake manifold
Intake manifold bolts 9.4 Nm (0.96 kg-m, 83 in-lb)
No. 6 means double tightening of bolt No. 1
Camshaft brackets
Step 1 (bolts 9 - 11) 2.0 Nm (0.2 kg-m, 17 in-lb)
Step 2 (bolts 1 - 8) 2.0 Nm (0.2 kg-m, 17 in-lb)
Step 3 (bolts 1 - 11) 5.9 Nm (0.6 kg-m, 52 in-lb)
Step 4 (bolts 1 - 11) 10.4 Nm (1.1 kg-m, 92 in-lb)
Camshaft sprocket (INT) 103 Nm (11 kgf-m, 76 ft lb)
Camshaft sprocket (EXH) 142 Nm (14 kgf-m, 105 ft lb)
Exhaust manifold 41.7 Nm (4.3 kgf-m, 31 ft lb)
Tighten nuts in numerical order as shown again
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
