Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1996 Suzuki Esteem GL, AutomaticFACTORY OEM SERVICE PROCEDURE
DTC Definition
DTC IDENTIFICATION
| DTC | System Affected | Condition |
|---|---|---|
| P0106 | MAP Sensor Circuit | Poor MAP Sensor Performance |
| P0107 | MAP Sensor Circuit | Low MAP Sensor Circuit Input |
| P0108 | MAP Sensor Circuit | High MAP Sensor Circuit Input |
| P0112 | IAT Sensor Circuit | Low IAT Sensor Circuit Input |
| P0113 | IAT Sensor Circuit | High IAT Sensor Circuit Input |
| P0117 | ECT Sensor Circuit | Low ECT Sensor Circuit Input |
| P0118 | ECT Sensor Circuit | High ECT Sensor Circuit Input |
| P0121 | TP Sensor Circuit | Poor TP Sensor Performance |
| P0122 | TP Sensor Circuit | Low TP Sensor Circuit Input |
| P0123 | TP Sensor Circuit | High TP Sensor Circuit Input |
| P0125 | ECT Sensor Circuit | Insufficient Coolant Temperature For Closed Loop Operation |
| P0131 | HO2S No. 1 Circuit | Low HO2S No.1 Circuit Input |
| P0132 | HO2S No. 1 Circuit | High HO2S No.1 Circuit Input |
| P0133 | HO2S No. 1 Circuit | Slow Response Of HO2S No.1 Circuit |
| P0134 | HO2S No. 1 Circuit | No HO2S No. 1 Ckt Activity Detected |
| P0135 | HO2S No. 1 Heater Circuit | HO2S No. 1 Heater Circuit Malfunction |
| P0136 | HO2S No. 2 Circuit | HO2S No. 2 Circuit Malfunction |
| P0141 | HO2S No. 2 Heater Circuit | HO2S No. 2 Heater Circuit Malfunction |
| P0171 | Fuel System Lean | Total Fuel Trim Is Greater Than Allowed Specification |
| P0172 | Fuel System Rich | Total Fuel Trim Is Less Than Allowed Specification |
| P0300 | Random Misfire Detected | Electrical Or Mechanical Misfire (Catalyst Damaging) |
| P0301 | Cylinder No. 1 Misfire | Electrical Or Mechanical Misfire Common To One Cylinder |
| P0302 | Cylinder No. 2 Misfire | Electrical Or Mechanical Misfire Common To One Cylinder |
| P0303 | Cylinder No. 3 Misfire | Electrical Or Mechanical Misfire Common To One Cylinder |
| P0304 | Cylinder No. 4 Misfire | Electrical Or Mechanical Misfire Common To One Cylinder |
| P0335 | CKP Sensor Circuit | No CKP Sensor Signal (Engine Running) |
| P0340 | CMP Sensor Circuit | No CMP Sensor Signal For 2 Seconds During Engine Cranking |
| P0400 | EGR Flow Malfunction | Excessive Or Insufficient EGR Flow |
| P0420 | Catalyst Efficiency Low | HO2S No. 1 & 2 Output Is Similar |
| P0443 | Canister Purge Control Valve Circuit | Canister Purge Control System Malfunction |
| P0461 | Fuel Level Sensor Circuit | Poor Fuel Level Sensor Circuit Performance |
| P0463 | Fuel Level Sensor Ckt | High Voltage Input |
| P0500 | Vehicle Speed Sensor Malfunction | No Signal In "D" Range |
| P0505 | Idle Control System Malfunction | Target Idle Speed Not Obtained |
| P0510 | CTP Switch Malfunction | No CTP Switch Activity |
| P0601 | PCM Memory Check Sum Error | Data Write Error |
| P0603 | PCM Keep Alive Memory Error | EEPROM Memory Error |
| P1450 | Barometric Pressure Sensor | Low Or High Input |
| P1451 | Barometric Pressure Sensor | Barometric Pressure Sensor Performance Problem During Cranking |
| P1460 | Radiator Fan Control System | High Fan Control Relay Terminal Voltage With Low Coolant Temp. |
| P1500 | Engine Starter Signal Circuit | No Input Or Constant Input From Starter Signal Circuit |
| P1510 | PCM Back-Up Power Supply Malfunction | No Back-Up Power Supply After Engine Start |
| P1530 | Ignition Timing Adjustment Switch Ckt | Test Switch Terminal Shorted To Ground |
| P1600 | Serial Communication PCM/TCM | No Signal Or Check Sum Error While Engine Running |
| P1717 | A/T Drive Range Signal | No "D" Range Signal During |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.
