Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2025 Subaru Outback BaseFACTORY OEM SERVICE PROCEDURE
VDC Control Module and Hydraulic Control Unit (VDCCM & H/U): Installation
CAUTION:
- When installing the VDC Control Module & H/U to the VDC Control Module & H/U bracket, make sure that there is no oil adhered to the bolts and the threads of VDC Control Module & H/U. If the oil is adhered, degrease it carefully before tightening.
- Connect the VDC Control Module & H/U connector securely.
- When the hydraulic unit assembly VDC has been replaced, be sure to perform the module registration.
- Install the bracket COMPL hydraulic unit VDC and the hydraulic unit assembly VDC.
- Attach the bracket COMPL hydraulic unit VDC.
Tightening torque:
33 N.m (3.4 kgf-m, 24.3 ft-lb)
- Install the bracket hydraulic unit adapter to the hydraulic unit assembly VDC.
Tightening torque:
27 N.m (2.8 kgf-m, 19.9 ft-lb)
- Install the hydraulic unit sub assembly to the bracket COMPL hydraulic unit VDC.
Tightening torque:
7.5 N.m (0.8 kgf-m, 5.5 ft-lb)
- Install the pipe assembly front ABS using a flare nut wrench and a crowfoot wrench.NOTE: If the work can be performed with the front and back sides reversed, it is also possible to use a 6-point crowfoot wrench.TIGHTENING TORQUE SPECIFICATION
Calculation formula T1 = 15 N.m (1.5 kgf-m, 11.1 ft-lb) x L1/(L1 + L2) T2 = 19 N.m (1.9 kgf-m, 14.0 ft-lb) x L1/(L1 + L2) T: Reading of the torque wrench L1: Effective length of the torque wrench L2: Effective length of the crowfoot wrench NOTE: If the effective length of the tool used is unknown, consult the manufacturer of the tool.(a) Effective length of the crowfoot wrench (L2) (b) Effective length of the torque wrench (L1) (c) Center of the open end of crowfoot wrench (d) Center of drive square of the torque wrench (e) Center of the position where a force is applied by hand - Connect the hydraulic unit assembly VDC connector.
- Attach the bracket COMPL hydraulic unit VDC.
- Install the air intake boot.
- H4DO model: Ref. to INTAKE (INDUCTION) (H4DO)>AIR INTAKE BOOT>INSTALLATION .
- H4DOTC model: Ref. to INTAKE (INDUCTION) (H4DOTC)>AIR INTAKE BOOT>INSTALLATION .
- Connect the ground terminal to battery sensor. Ref. to REPAIR CONTENTS>NOTE>BATTERY .
- Bleed air from the brake system. Ref. to BRAKE>AIR BLEEDING>PROCEDURE .
- Using the Subaru Select Monitor, perform parameter confirmation, selection, and registration.NOTE:
- When the VDC Control Module & H/U is replaced, be sure to perform the parameter selection/registration and the module registration.
- When the registration has not been performed, the DTC code [SELECTED PARAMETER] is detected together with the ABS/EBD/VDC warning light illumination.
- Check that the applied model and grade of the relevant vehicle are included. Ref. to VEHICLE DYNAMICS CONTROL (VDC)>VDC CONTROL MODULE AND HYDRAULIC CONTROL UNIT (VDCCM & H/U)>MAINTENANCE MODE>VDCCM PARAMETER CHECK .
- If the applied model and grade of the target vehicle are not included, perform "parameter selection and registration". Ref. to VEHICLE DYNAMICS CONTROL (VDC)>VDC CONTROL MODULE AND HYDRAULIC CONTROL UNIT (VDCCM & H/U)>MAINTENANCE MODE>VDCCM PARAMETER SELECTION .
- When the hydraulic unit assembly VDC is replaced, perform the module registration. Ref. to COMMON (DIAGNOSTICS)>UNIT REGISTRATION>OPERATION .
- Perform "VDC sensor midpoint setting mode". Ref. to VEHICLE DYNAMICS CONTROL (VDC)>VDC CONTROL MODULE AND HYDRAULIC CONTROL UNIT (VDCCM & H/U)>ADJUSTMENT>VDC SENSOR MIDPOINT SETTING MODE .
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
