2025 Subaru Crosstrek BaseFACTORY OEM SERVICE PROCEDURE

Select Cable: Installation

CAUTION:
  • Check that the protector (b) is set between the clamps (a).
  • If the protector (b) is offset, set it between the clamps (a).
G13935596Courtesy of SUBARU OF AMERICA, INC.
  1. Set a new clamp on the select lever as shown in the figure.
    G16767447Courtesy of SUBARU OF AMERICA, INC.
    (A) Front side
    (B) Upside
  2. Install the select cable to the select lever. (If the connector pin is not removed)
    CAUTION:
    • Install the cable so that it does not twist.
    • Check that the select lever is in "N range".
    • If the connector pin is removed, always replace with a new connector pin.
    • Do not apply load while holding the part (a).

      Doing so may damage the inside of the select cable.

    G14602404Courtesy of SUBARU OF AMERICA, INC.
    1. Insert the select cable to the connector pin.
    2. Secure the select cable to the clamp.
      G14602410Courtesy of SUBARU OF AMERICA, INC.
  3. Install the select cable to the select lever. (If the connector pin is removed)
    CAUTION:
    • Install the cable so that it does not twist.
    • Check that the select lever is in "N" range.
    • Do not apply excessive load while holding the part (a).

      Doing so may damage the inside of the select cable.

    G14602404Courtesy of SUBARU OF AMERICA, INC.
    1. Secure the select cable to the clamp.
    2. Align the cable thread with the select lever arm.
      G16767451Courtesy of SUBARU OF AMERICA, INC.
    3. Install a new connector pin.
      G16767452Courtesy of SUBARU OF AMERICA, INC.
  4. Temporarily Install the adjusting nut (rear) to the select cable.
  5. Apply grease to the shifter arm.

    Preparation items  :

    Grease (VIN:] JF1############## [model and] JF2############## [model) 

    IDEMITSU APOLLOIL AUTOLEX A, NIPPON GREASE NIGTIGHT LTS No. 2 or equivalent

    Grease (VIN:] 4S4############## [model) 

    Shell Gadus S2 V220, NIPPON GREASE NIGTIGHT LTS No. 2 or equivalent

    G00659600Courtesy of SUBARU OF AMERICA, INC.
  6. Install the cable plate.

    Tightening torque: 

    25 N.m (2.5 kgf-m, 18.4 ft-lb)

    G16767441Courtesy of SUBARU OF AMERICA, INC.
  7. Connect the select cable to the transmission main body.
    CAUTION: Do not apply excessive load while holding the part (a).

    Doing so may damage the inside of the select cable.

    G14602401Courtesy of SUBARU OF AMERICA, INC.
    NOTE: Set the washer before installing the snap pin.

    Tightening torque: 

    18 N.m (1.8 kgf-m, 13.3 ft-lb)

    G16767440Courtesy of SUBARU OF AMERICA, INC.
  8. Adjust the select cable free play. Ref. to CONTROL SYSTEMS>SELECT CABLE>ADJUSTMENT .
  9. Install the center exhaust cover. Ref. to EXHAUST (H4DO)>REAR EXHAUST PIPE .
  10. Release the shift lock and shift the select lever to the "P" range. Ref. to CONTROL SYSTEMS>SELECT LEVER>INSTALLATION .
Chapter Navigation
Return to Chapter: Select Cable
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.