2023 Subaru Outback WildernessFACTORY OEM SERVICE PROCEDURE

Converter Case Cover: Installation

  1. Select the front reduction drive gear shim.
    1. Measure the height "H1" from the converter case cover upper face to the ball bearing catch surface.
      G16389871Courtesy of SUBARU OF AMERICA, INC.
      (A) Measurement surface
    2. Using the ST, measure the height "H2" from the ST end face to the converter case cover mating surface.

      Preparation tool: 

      ST: GAUGE (499575600)

      G16389872Courtesy of SUBARU OF AMERICA, INC.
      (A) Measurement surface
    3. Using the ST, measure the height "H3" from the ST end face to the ball bearing end face.

      Preparation tool: 

      ST: GAUGE (499575400)

      G16389873Courtesy of SUBARU OF AMERICA, INC.
      (A) Measurement surface
    4. Using the following calculation and selection criteria table, select an appropriate thickness of the front reduction drive gear shim.
      NOTE: Adjust using 1 piece.

      C = (H3 - 15 mm (0.6 in)) - ((H2 - 15 mm (0.6 in)) - H1)

    C Clearance mm (in)
    H1 Measured value (mm (in)) of step (1)
    H2 Measured value (mm (in)) of step (2)
    H3 Measured value (mm (in)) of step (3)
    15 mm (0.6 in) Thickness of ST

    Selection criteria table for front reduction drive gear shim according to calculated values 

    Clearance "C" mm (in) Front reduction drive gear shim thickness mm (in)
    1.070 - 1.174 (0.042 - 0.046) 1.0 (0.039)
    1.175 - 1.274 (0.046 - 0.050) 1.1 (0.043)
    1.275 - 1.374 (0.050 - 0.054) 1.2 (0.047)
    1.375 - 1.474 (0.054 - 0.058) 1.3 (0.051)
    1.475 - 1.580 (0.058 - 0.062) 1.4 (0.055)
  2. Select the front reduction driven gear shim (front side).
    1. Measure the height "H1" from the converter case cover upper face to the ball bearing catch surface.
      G16389874Courtesy of SUBARU OF AMERICA, INC.
      (A) Measurement surface
    2. Using the ST, measure the height "H2" from the ST end face to the converter case cover mating surface.

      Preparation tool: 

      ST: GAUGE (499575600)

      G16389875Courtesy of SUBARU OF AMERICA, INC.
      (A) Measurement surface
    3. Set a new ball bearing to the reduction driven gear.
    4. Using the ST, measure the height "H3" from the ST end face to the ball bearing end face.

      Preparation tool: 

      ST: GAUGE (499575400)

      G16389876Courtesy of SUBARU OF AMERICA, INC.
      (A) Measurement surface
    5. Using the following calculation and selection criteria table, select an appropriate thickness of the front reduction driven gear shim (front side).
      NOTE: Adjust using 1 - 2 pieces.

      C = (H3 - 15 mm (0.6 in)) - ((H2 - 15 mm (0.6 in)) - H1)

      C Clearance mm (in)
      H1 Measured value (mm (in)) of step (1)
      H2 Measured value (mm (in)) of step (2)
      H3 Measured value (mm (in)) of step (4)
      15 mm (0.6 in) Thickness of ST

      Selection criteria table for front reduction driven gear shim (front side) according to calculated values 

      Clearance "C" mm (in) Front reduction driven gear shim (front side) thickness mm (in)
      0.470 - 0.569 (0.019 - 0.022) 0.4 (0.016)
      0.570 - 0.669 (0.022 - 0.026) 0.5 (0.020)
      0.670 - 0.769 (0.026 - 0.030) 0.6 (0.024)
      0.770 - 0.869 (0.030 - 0.034) 0.7 (0.028)
      0.870 - 0.980 (0.034 - 0.039) 0.8 (0.031)
    6. Remove the ball bearing from the reduction driven gear.
  3. Install a new seal ring.
    NOTE:
    • Apply CVTF to the seal rings.
    • Do not stretch the seal ring more than necessary.
    G13622349Courtesy of SUBARU OF AMERICA, INC.
  4. Install the front reduction driven gear shim (front side).
    G13622348Courtesy of SUBARU OF AMERICA, INC.
  5. Using the ST and a press, press-fit a new ball bearing.
    NOTE: Apply CVTF to the press-fitting area.

    Preparation tool: 

    ST: INSTALLER (20099AE020)

    G13622358Courtesy of SUBARU OF AMERICA, INC.
  6. Using vaseline, set the front reduction drive gear shim.
    G14611530Courtesy of SUBARU OF AMERICA, INC.
  7. Install a new O-ring.
    NOTE: Apply CVTF to the O-rings.
    G13622345Courtesy of SUBARU OF AMERICA, INC.
  8. Apply liquid gasket to the mating surface of the converter case cover as shown in the figure, and temporarily install the converter case cover.
    NOTE:
    • Before applying liquid gasket, degrease the liquid gasket seal surface of the converter case and converter case cover.
    • Install within 5 min. after applying liquid gasket.

    Preparation items: 

    Liquid gasket: THREE BOND 1215B or equivalent

    G14611532Courtesy of SUBARU OF AMERICA, INC.
    G13200347Courtesy of SUBARU OF AMERICA, INC.
  9. Tighten the bolts securing the converter case cover.

    Tightening torque: 

    24 N.m (2.4 kgf-m, 17.7 ft-lb)

  10. Install the oil pump chain cover and the oil pump chain. Ref. to CONTINUOUSLY VARIABLE TRANSMISSION (TR690)>OIL PUMP CHAIN>INSTALLATION .
  11. Install the oil stopper plate (A) and lubrication pipe (B).

    Tightening torque: 

    9 N.m (0.9 kgf-m, 6.6 ft-lb)

    G13622342Courtesy of SUBARU OF AMERICA, INC.
  12. Install the drive pinion. Ref. to CONTINUOUSLY VARIABLE TRANSMISSION (TR690)>DRIVE PINION>INSTALLATION .
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.