Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2023 Subaru Crosstrek Base, Standard TransFACTORY OEM SERVICE PROCEDURE
System Block Diagram
| (1) | Engine control module |
| (2) | Ignition coil and Electronic ignition |
| (3) | Crankshaft position sensor |
| (4) | Intake camshaft position sensor |
| (5) | Electronic control throttle |
| (6) | Fuel injector |
| (7) | Engine coolant temperature sensor |
| (8) | Manifold absolute pressure sensor |
| (9) | Intake air temperature sensor & Mass airflow sensor |
| (10) | EVAP canister purge valve |
| (11) | Knock sensor |
| (12) | Positive crankcase ventilation valve |
| (13) | Air cleaner |
| (14) | Canister |
| (15) | Ignition relay |
| (16) | Fuel pump relay |
| (17) | Fuel filter |
| (18) | Fuel pump |
| (19) | Front catalyst |
| (20) | Rear catalyst |
| (21) | Primary oxygen sensor |
| (22) | Secondary oxygen sensor |
| (23) | Radiator fan control Relay |
| (24) | Radiator fan |
| (25) | Malfunction indicator lamp |
| (26) | Air filter |
| (27) | Park/Neutral position switch |
| (28) | Fuel level sensor |
| (29) | Resonator chamber |
| (30) | Electronically controlled EGR |
| (31) | Oil control valve for in-VVT |
| (32) | Engine oil temperature sensor |
| (33) | Evaporative leak check module |
| (34) | Tumble generator valve motors and tumble generator valve position switch |
| (35) | Inhibitor switch for continuously variable transmission vehicle |
| (36) | Acceleration pedal position sensor |
| (37) | Exhaust camshaft position sensor |
| (38) | Oil control valve for ex-VVT |
| (39) | EGR Cooler |
| (40) | High-pressure fuel pump |
| (41) | High-pressure fuel sensor |
| (42) | Transmission control unit |
| (43) | ABS unit or VDC unit |
| (44) | T/M control unit (CVT) |
| (45) | Car speed |
| (46) | SELECT MONITOR |
| (47) | Ignition switch |
| (48) | A/C Relay |
| (49) | A/C Control unit |
| (50) | A/C Compressor |
| (51) | IG l |
| (1) | Electronic Control Unit |
| (2) | Starter |
| (3) | Fuel Tank |
| (4) | Air Flow Meter |
| (5) | Direct Fuel Injector |
| (6) | Cam Angle Sensor |
| (7) | Oxygen Sensor |
| (8) | A/F Sensor |
| (9) | High-pressure fuel pump |
| (10) | Coolant Temperature Sensor |
| (11) | Pressure Sensor |
| (12) | Throttle Body |
| (13) | Cam Angle Sensor |
| (14) | Fuel Pressure Sensor |
| (15) | Direct Fuel Injector |
| (16) | Crank Angle Sensor |
| (17) | Fuel Filter |
| (18) | Pressure Regulator |
| (19) | Low Pressure Fuel Pump |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.