Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Intake Manifold Assembly: Installation
- Install the cylinder head plate to the cylinder head.
- Install the fuel pipe protector stay.
Tightening torque:
19 N.m (1.9 kgf-m, 14.0 ft-lb)
- Set a new gasket and install the intake manifold assembly.NOTE:
Be careful not to let the engine wiring harness be caught by the parts.
Tightening torque:
25 N.m (2.5 kgf-m, 18.4 ft-lb)
- Set a new gasket, and install the stud bolts using TORX® E5.
Tightening torque:
6.4 N.m (0.7 kgf-m, 4.7 ft-lb)
- Temporarily attach the EGR pipe No. 2 and tighten it in order of (1)→(2)→(3).
Tightening torque:
9 N.m (0.9 kgf-m, 6.6 ft-lb)
- Install the PCV hose. Ref. to EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) (H4DOTC)>PCV HOSE>INSTALLATION
- Install the harness stay.
Tightening torque:
6.4 N.m (0.7 kgf-m, 4.7 ft-lb)
- Install the clip (A) and clip (B) to the harness stay.
- Connect the connector (A).
- Install the clip (B) and clip (C).
- Install the clip (C) and clip (D).
- Connect the fuel delivery pipe (B). Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>FUEL DELIVERY AND EVAPORATION LINES>INSTALLATION>QUICK CONNECTOR CONNECTION (TYPE B)
- Connect the connector (A).
- Install the fuel pipe protector No. 2.
Tightening torque:
19 N.m (1.9 kgf-m, 14.0 ft-lb)
- Install the fuel pipe protector No. 1.
Tightening torque:
25 N.m (2.5 kgf-m, 18.4 ft-lb)
- Set the engine wiring harness and secure the engine wiring harness to the bracket with the claw.
- Install the engine wiring harness to the clip (A), and connect the connector (B).
- Connect the connector (C) and connector (D) in numerical order shown in figure.
- Secure the battery cable assembly with the claw (B) and clip (A).
- Secure the battery cable assembly with the clip (A).
- Connect the connector (B), connector (C) and terminal (D).
Tightening torque:
15.5 N.m (1.6 kgf-m, 11.4 ft-lb)
- Install the V-belt cover.NOTE:
- Check the grommet for peel-off or disengagement.
- Be careful not to deform the bracket during installation.
Tightening torque:
7 N.m (0.7 kgf-m, 5.2 ft-lb)
- Connect the evaporation hose (E).
- Install the fuel delivery tube clamp (D).
- Connect the fuel delivery tube (C). Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>FUEL DELIVERY AND EVAPORATION LINES>INSTALLATION>QUICK CONNECTOR CONNECTION (TYPE A)
- Connect the connector (A) and connector (B).
- Connect the PCV pipe assembly to the intake duct No. 1, and lock it.CAUTION:
- Make sure there are no damage or dust on connections. If necessary, clean the seal surface of the pipe.
- Confirm that the connections are secure.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.