Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Ignition Control System
Wiring diagram:Â
Engine Electrical System Ref. to WIRING SYSTEM (IMPREZA MODEL)>ENGINE ELECTRICAL SYSTEM>WIRING DIAGRAM . Ref. to WIRING SYSTEM (CROSSTREK MODEL (EXCEPT FOR HEV))>ENGINE ELECTRICAL SYSTEM>WIRING DIAGRAM .
Use the check board when measuring the ECM terminal voltage and resistance. Ref. to  ENGINE (DIAGNOSTICS) (H4DO 2.0 (EXCEPT FOR HEV))>GENERAL DESCRIPTION>PREPARATION TOOL>HOW TO USE CHECK BOARD .Â
- CHECK SPARK PLUG CONDITIONÂ
.
- Remove the spark plug. Ref. to IGNITION (H4DO (EXCEPT FOR HEV))>SPARK PLUG>REMOVAL .
- Check the spark plug condition. Ref. to IGNITION (H4DO (EXCEPT FOR HEV))>SPARK PLUG>INSPECTION
.
Is the check result OK?
Yes: Go to  2.
No:Â Replace the spark plug. Ref. to IGNITION (H4DO (EXCEPT FOR HEV))>SPARK PLUG .
- CHECK IGNITION SYSTEM FOR SPARKSÂ
.
- Connect the spark plug to ignition coil.
- Release the fuel pressure. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO (EXCEPT FOR HEV))>FUEL>PROCEDURE>RELEASING OF FUEL PRESSURE .
- Contact the spark plug thread portion to engine.
- While opening the throttle valve fully, crank the engine to check that spark occurs at each cylinder.
Does spark occur at each cylinder?
Yes:Â Check fuel pump system. Ref. to ENGINE (DIAGNOSTICS) (H4DO 2.0 (EXCEPT FOR HEV))>DIAGNOSTICS WITH PHENOMENON>FUEL PUMP CIRCUITÂ .
No: Go to  3.
- CHECK IGNITION COIL POWER SUPPLY CIRCUITÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from ignition coil.
- Turn the ignition switch to ON.
- Measure the voltage between ignition coil connector and engine ground.
Connector & terminalÂ
(E31) No. 1 (+) - Engine ground (-):
(E32) No. 1 (+) - Engine ground (-):
(E33) No. 1 (+) - Engine ground (-):
(E34) No. 1 (+) - Engine ground (-):
Is the voltage 10 V or more?
Yes: Go to  4.
No:Â Repair the harness and connector.
NOTE:In this case, repair the following item:Â
- Open or short to ground in harness of power supply circuitÂ
- Poor contact of coupling connectorÂ
- Blown out of fuseÂ
- CHECK HARNESS OF IGNITION COIL GROUND CIRCUITÂ
.
- Turn the ignition switch to OFF.
- Measure the resistance of harness between ignition coil connector and engine ground.
Connector & terminalÂ
(E31) No. 3 - Engine ground:
(E32) No. 3 - Engine ground:
(E33) No. 3 - Engine ground:
(E34) No. 3 - Engine ground:
Is the resistance less than 5 Ω?
Yes: Go to  5.
No:Â Repair the open circuit in harness between ignition coil connector and engine ground.
- CHECK HARNESS BETWEEN ECM AND IGNITION COIL CONNECTORÂ
.
- Disconnect the connector from ECM.
- Measure the resistance of harness between ECM connector and ignition coil connector.
Connector & terminalÂ
(E158) No. 10 - (E31) No. 2:
(E158) No. 11 - (E32) No. 2:
(E158) No. 12 - (E33) No. 2:
(E158) No. 13 - (E34) No. 2:
Is the resistance less than 1 Ω?
Yes: Go to  6.
No:Â Repair the open circuit in harness between ECM connector and ignition coil connector.
- CHECK HARNESS BETWEEN ECM AND IGNITION COIL CONNECTORÂ
.
Measure the resistance of harness between ECM connector and engine ground.
Connector & terminalÂ
(E158) No. 10 - Engine ground:
(E158) No. 11 - Engine ground:
(E158) No. 12 - Engine ground:
(E158) No. 13 - Engine ground:
Is the resistance 1 MΩ or more?
Yes: Go to  7.
No:Â Repair the ground short circuit of harness between ECM connector and ignition coil connector.
- CHECK FOR POOR CONTACTÂ
.
Check for poor contact of ECM connector.
Is there poor contact of ECM connector?
Yes:Â Repair the poor contact of ECM connector.
No:Â Replace the ignition coil. Ref. to IGNITION (H4DO (EXCEPT FOR HEV))>IGNITION COIL .
NOTE:After the faulty parts are repaired or replaced, perform the final check in Basic Diagnostic Procedure. Ref. to  ENGINE (DIAGNOSTICS) (H4DO 2.0 (EXCEPT FOR HEV))>BASIC DIAGNOSTIC PROCEDURE>PROCEDURE .Â
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
