Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Basic Diagnostic Procedure: Procedure
- PERFORM CUSTOMER INTERVIEW
.
Ask the customer when and how the trouble occurred using the Check List for Interview. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>CHECK LIST FOR INTERVIEW .
Did you interview the customer?
Yes : Go to 2.
No : Perform the interview, and Go to 2.
- PERFORM BASIC INSPECTION
.
Perform basic inspection. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>General Description>INSPECTION .
Is the check result OK?
Yes : Go to 3.
No : Repair the faulty part found in basic inspection, and Go to 3.
- CHECK SUBARU SELECT MONITOR COMMUNICATION
.
- Turn the ignition switch to OFF.
- Connect the Subaru Select Monitor to data link connector. Ref. to COMMON (diag)>DATA LINK CONNECTOR .
- Turn the ignition switch to ON and run the Subaru Select Monitor.
- Select [Multi-Function Display].NOTE: For detailed operation procedures, refer to "Help" of application.
Is communication possible?
Yes : Go to 4.
No : Check the communication circuit. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>DIAGNOSTIC PROCEDURE FOR SUBARU SELECT MONITOR COMMUNICATION .
- CHECK CAN COMMUNICATION
.
Perform the diagnosis for LAN system. Ref. to LAN SYSTEM (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
Is the check result OK?
Yes : Go to 5.
No : Perform the inspection according to the diagnosis for LAN system.
- CHECK MFD
.
Read the DTC of [Multi-Function Display] using the Subaru Select Monitor. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .
Are any DTCs displayed? (Current malfunction)
Yes : Record the DTC, time stamp and freeze frame data, and Go to 7.
No : Go to 6.
- CHECK MFD
.
Check MFD operation. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>ACTIVE TEST .
Is the check result OK?
Yes : System is normal. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>ACTIVE TEST .
No : Replace the MFD. Ref. to INSTRUMENTATION/DRIVER INFO>MULTI-FUNCTION DISPLAY (MFD) .
- PERFORM DIAGNOSIS
.
- Perform the diagnosis for the displayed DTCs.
- Repair or replace the cause of trouble.
- Using the Subaru Select Monitor, perform the clear memory of [Multi-Function Display]. Ref. to COMMON (diag)>CLEAR MEMORY .
- Execute the inspection mode.
- Read the DTC of [Multi-Function Display] using the Subaru Select Monitor. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .
Are any DTCs displayed? (Current malfunction)
Yes : Repeat step 7 until DTC is not shown. Go to 7.
No : Finish the diagnosis.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.