Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Ignition Control System
Wiring diagram:Â
Engine Electrical System Ref. to WIRING SYSTEM>ENGINE ELECTRICAL SYSTEM>WIRING DIAGRAM
Use the check board when measuring the ECM terminal voltage and resistance. Ref. to  ENGINE (DIAGNOSTICS) (H4DOTC)>GENERAL DESCRIPTION>PREPARATION TOOL>HOW TO USE CHECK BOARDÂ
- CHECK SPARK PLUG CONDITIONÂ
.
Remove the spark plug, and check the condition. Ref. to IGNITION (H4DOTC)>SPARK PLUG>INSPECTION
Is the check result OK?
Yes : Go to  2.
No : Replace the spark plug. Ref. to IGNITION (H4DOTC)>SPARK PLUG
- CHECK IGNITION SYSTEM FOR SPARKSÂ
.
- Connect the spark plug to ignition coil.
- Release the fuel pressure. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>FUEL>PROCEDURE>RELEASING OF FUEL PRESSURE
- Contact the spark plug thread portion to engine.
- While opening the throttle valve fully, crank the engine to check that spark occurs at each cylinder.
Does spark occur at each cylinder?
Yes : Check fuel pump system. Ref. to ENGINE (DIAGNOSTICS) (H4DOTC)>DIAGNOSTICS WITH PHENOMENON>FUEL PUMP CIRCUITÂ
No : Go to  3.
- CHECK IGNITION COIL POWER SUPPLYÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from ignition coil.
- Turn the ignition switch to ON.
- Measure the voltage between ignition coil connector and engine ground.
Connector & terminalÂ
(E111) No. 1 (+) - Engine ground (-):
(E112) No. 1 (+) - Engine ground (-):
(E113) No. 1 (+) - Engine ground (-):
(E114) No. 1 (+) - Engine ground (-):
Is the voltage 10 V or more?
Yes : Go to  4.
No : Repair the following item.
- Open or short to ground in harness of power supply circuit
- Poor contact of coupling connector
- Poor contact of J/C
- Blown out of fuse
- CHECK HARNESS OF IGNITION COIL GROUND CIRCUIT (OPEN)Â
.
- Turn the ignition switch to OFF.
- Measure the resistance of harness between ignition coil connector and engine ground.
Connector & terminalÂ
(E111) No. 3 - Engine ground:
(E112) No. 3 - Engine ground:
(E113) No. 3 - Engine ground:
(E114) No. 3 - Engine ground:
Is the resistance less than 5 Ω?
Yes : Go to  5.
No : Repair the open circuit in harness between ignition coil connector and engine ground.
- CHECK HARNESS BETWEEN ECM AND IGNITION COIL CONNECTOR (OPEN)Â
.
- Disconnect the connector from ECM.
- Measure the resistance of harness between ECM connector and ignition coil connector.
Connector & terminalÂ
(E51) No. 10 - (E111) No. 2:
(E51) No. 26 - (E112) No. 2:
(E51) No. 42 - (E113) No. 2:
(E51) No. 58 - (E114) No. 2:
Is the resistance less than 1 Ω?
Yes : Go to  6.
No : Repair the open circuit in harness between ECM connector and ignition coil connector.
- CHECK HARNESS BETWEEN ECM AND IGNITION COIL CONNECTOR (SHORT TO GROUND)Â
.
Measure the resistance of harness between ECM connector and engine ground.
Connector & terminalÂ
(E51) No. 10 - Engine ground:
(E51) No. 26 - Engine ground:
(E51) No. 42 - Engine ground:
(E51) No. 58 - Engine ground:
Is the resistance 1 MΩ or more?
Yes : Go to  7.
No : Repair the ground short circuit of harness between ECM connector and ignition coil connector.
- CHECK FOR POOR CONTACTÂ
.
Check for poor contact of ECM connector.
Is there poor contact of ECM connector?
Yes : Repair the poor contact of ECM connector.
No : Replace the ignition coil. Ref. to IGNITION (H4DOTC)>IGNITION COIL
After the faulty parts are repaired or replaced, perform the final check in Basic Diagnostic Procedure. Ref. to  ENGINE (DIAGNOSTICS) (H4DOTC)>BASIC DIAGNOSTIC PROCEDURE>PROCEDUREÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
