2021 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE

Engine Assembly: Removal

WARNING: This page is about a different car, the 2022 Subaru WRX. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the striker assembly front hood. Ref. to EXTERIOR BODY PANELS>FRONT HOOD>DISASSEMBLY
    NOTE:

    This procedure is necessary to prevent the lifting device and the striker assembly front hood from contacting with each other and causing damage. However, the procedure may be omitted if it is assured that the lifting device to be used will not make a contact. 

  2. Fully open the panel COMPL front hood. Ref. to REPAIR CONTENTS>NOTE>FRONT HOOD GAS STAY
  3. Release the fuel pressure. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>FUEL>PROCEDURE>RELEASING OF FUEL PRESSURE
  4. Open the fuel filler lid and remove the fuel filler cap.
    NOTE:

    This operation is required to release the inner pressure of the fuel tank. 

  5. Disconnect the ground terminal from battery sensor. Ref. to REPAIR CONTENTS>NOTE>BATTERY
  6. Collect the refrigerant. Ref. to AIR CONDITIONER>REFRIGERANT RECOVERY PROCEDURE>PROCEDURE
  7. Remove the radiator. Ref. to COOLING (H4DOTC)>RADIATOR>REMOVAL
  8. Remove the crossmember support rear RH. Ref. to FRONT SUSPENSION>CROSSMEMBER SUPPORT>REMOVAL
  9. Remove the intake duct No. 1 and intake duct No. 2.

    Intake duct No. 1: 

    Ref. to INTAKE (INDUCTION) (H4DOTC)>Intake Duct>REMOVAL>INTAKE DUCT NO. 1

    Intake duct No. 2: 

    Ref. to INTAKE (INDUCTION) (H4DOTC)>INTAKE DUCT>REMOVAL>INTAKE DUCT NO. 2

  10. Remove the intercooler. Ref. to INTAKE (INDUCTION) (H4DOTC)>INTERCOOLER>REMOVAL
  11. Disconnect the connector (A), connector (B) and terminal (C), and remove the clip (D).
  12. Disconnect the hose - pressure suction and the hose - pressure discharge from the A/C compressor. Ref. to AIR CONDITIONER>HOSE AND PIPE>REMOVAL
    G14610567Courtesy of SUBARU OF AMERICA, INC.
  13. Remove clip (A) securing battery cable assembly.
  14. Remove the claw (B) securing the battery cable assembly, and place it aside so that it does not interfere with work.
    G14600902Courtesy of SUBARU OF AMERICA, INC.
  15. Remove the connector (A) and connector (B) in numerical order shown in figure.
  16. Disconnect the connector (C), and remove the engine wiring harness from the clip (D).
    G14600903Courtesy of SUBARU OF AMERICA, INC.
  17. Release the claw securing the engine wiring harness to the bracket, and place it aside so that it does not interfere with work.
    G14600904Courtesy of SUBARU OF AMERICA, INC.
  18. Disconnect the heater inlet hose (A) and the heater outlet hose (B).
    G14610571Courtesy of SUBARU OF AMERICA, INC.
  19. Disconnect the connector (A), connector (B), connector (C), and remove the clip (D), clip (E) and clip (F). (CVT model)
    G14610572Courtesy of SUBARU OF AMERICA, INC.
  20. Disconnect the connector (A) and connector (B), and remove the bolt securing the vacuum pipe to the engine rear hanger. (MT model)
    G14610573Courtesy of SUBARU OF AMERICA, INC.
  21. Remove the pitching stopper.

    CVT model: 

    Ref. to CONTINUOUSLY VARIABLE TRANSMISSION (TR690)>TRANSMISSION MOUNTING SYSTEM>REMOVAL>PITCHING STOPPER

    MT model: 

    Ref. to MANUAL TRANSMISSION AND DIFFERENTIAL (TY75)>TRANSMISSION MOUNTING SYSTEM>REMOVAL>PITCHING STOPPER

  22. Disconnect the water hose from CVTF cooler (with warmer feature). (CVT model)
    G14610574Courtesy of SUBARU OF AMERICA, INC.
  23. Disconnect the brake booster vacuum hose from the brake vacuum pump, and place it aside so that it does not interfere with the work. (MT model)
    NOTE:

    Before disconnecting the brake booster vacuum hose, use a marker to put an alignment mark (a) at the position shown in the figure when the clip is slid. 

    G13862471Courtesy of SUBARU OF AMERICA, INC.
    G14610576Courtesy of SUBARU OF AMERICA, INC.
  24. Remove the front exhaust pipe. Ref. to EXHAUST (H4DOTC)>FRONT EXHAUST PIPE>REMOVAL
  25. Set the ST between the vehicle and the rear crossmember. (CVT model)
    CAUTION:

    Be sure to use the M10 x 60 x 1.25 bolts in the strength range of 8.8 (8.8 or 8 stamped on bolt head) or more in order to avoid damage to the vehicle body. 

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.