2021 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE

Engine Assembly: Installation

WARNING: This page is about a different car, the 2022 Subaru WRX. However, it is still accessible from the selected car via links, so may be relevant.
  1. Using the ST1, install the ST2 to the engine unit.

    Preparation tool: 

    ST1: BOLT (18363AA050)

    ST2: HANGER (18360AA040)

    Tightening torque: 

    43 N.m (4.4 kgf-m, 31.7 ft-lb)

    G14610591Courtesy of SUBARU OF AMERICA, INC.
  2. Support the engine unit with a lifting device and wire ropes, and remove the engine unit from the engine stand, etc.
  3. Install the engine mounting onto the engine unit.

    Tightening torque: 

    35 N.m (3.6 kgf-m, 25.8 ft-lb)

  4. Place the engine unit in engine compartment and align it with transmission body. (CVT model)
    NOTE:
    • Be careful not to damage adjacent parts or body panels with crank pulley, oil level gauge, etc. 
    • If it is hard to insert the knock pin on the engine unit into the transmission body, precisely adjust the height of the transmission body with garage jack so that no load is applied to the knock pin. 
  5. Apply a small amount of grease to splines of main shaft. (MT model)

    Preparation items: 

    Grease: NICHIMOLY N-130 or equivalent

  6. Position the engine unit in engine compartment, insert the clutch disc into the main shaft, and align it with the transmission body. (MT model)
    NOTE:
    • Be careful not to damage adjacent parts or body panels with crank pulley, oil level gauge, etc. 
    • If it is hard to insert the clutch disc into the main shaft, insert the wrench into the crank pulley bolt, and rotate the crank pulley slightly to insert it. 
    • If it is hard to insert the knock pin on the engine unit into the transmission body, precisely adjust the height of the transmission body with garage jack so that no load is applied to the knock pin. 
  7. With a lifting device and a garage jack, slowly lower the engine unit together with the transmission.
    NOTE:

    Check that the stud bolt of the engine mounting is securely inserted into the engine mounting hole of the crossmember COMPL front. 

  8. Install the bolts which hold the upper side of transmission to the engine unit.

    Tightening torque: 

    50 N.m (5.1 kgf-m, 36.9 ft-lb)

    • CVT model
      G14610594Courtesy of SUBARU OF AMERICA, INC.
    • MT model
      G14610595Courtesy of SUBARU OF AMERICA, INC.
  9. Remove the garage jack.
  10. Remove the lifting device and wire ropes.
  11. Remove the ST1 and ST2 from the engine unit.
    G14610591Courtesy of SUBARU OF AMERICA, INC.
  12. Install the torque converter to drive plate. (CVT model)
    1. Remove the ST from converter case.
      NOTE:

      Be careful not to drop the ST into the converter housing when removing the ST. 

      G14610588Courtesy of SUBARU OF AMERICA, INC.
    2. Insert the wrench into the crank pulley bolt, and rotate the crank pulley to attach the bolts (4 places) securing the torque converter to the drive plate.
      NOTE:

      Be careful not to drop bolts into the converter housing. 

      Tightening torque: 

      25 N.m (2.5 kgf-m, 18.4 ft-lb)

      G14610587Courtesy of SUBARU OF AMERICA, INC.
    3. Fit the plug to service hole.
      G14610586Courtesy of SUBARU OF AMERICA, INC.
  13. Install the starter. Ref. to STARTING/CHARGING SYSTEMS (H4DOTC)>STARTER>INSTALLATION
  14. Place the CVTF cooler (with warmer feature) to CVT, and temporarily tighten the upper bolt which secures the CVTF cooler (with warmer feature). (CVT model)
    G14610585Courtesy of SUBARU OF AMERICA, INC.
  15. Lift up the vehicle.
  16. Install the bolts and nuts which hold the lower side of transmission to the engine unit.

    Tightening torque: 

    50 N.m (5.1 kgf-m, 36.9 ft-lb)

    • CVT model
      G14610583Courtesy of SUBARU OF AMERICA, INC.
    • MT model
      G14610584Courtesy of SUBARU OF AMERICA, INC.
  17. Install the nuts which hold the engine mounting to the crossmember COMPL front.
    CAUTION:

    Be sure to use a new nut. 

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.