2021 Subaru Outback BaseFACTORY OEM SERVICE PROCEDURE

Inspection To Be Performed When The Select Lever Cannot Be Shifted From P Range

  1. CHECK DTC  .

    Read the DTC using Subaru Select Monitor.

    Is DTC detected?

    Yes  : Repair the corresponding system.

    NOTE: Before performing diagnosis for DTC, perform the basic inspection.

    Ref. to BODY CONTROL (DIAGNOSTICS)>GENERAL DESCRIPTION>INSPECTION .

    No  : Go to  2 .

    NOTE: Keep the Subaru Select Monitor connected while the ignition switch is ON.
  2. CHECK DTC  .
    1. Maintain the brake pedal depressed for one second or more.
    2. Read the DTC using Subaru Select Monitor.

    Is DTC B1016 displayed? (Current malfunction)

    Yes  : Check the corresponding system. Ref. to BODY CONTROL (DIAGNOSTICS)>DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)>DTC B1016: SHIFT LOCK CIRCUIT .

    No  : Go to  3 .

  3. CHECK CURRENT DATA  .

    Using Subaru Select Monitor, display [Stop Light Switch].

    Is "ON" displayed when the brake pedal is depressed and "OFF" displayed when the brake pedal is released?

    Yes  : Go to  4 .

    No  : Check the stop light system. Ref. to LIGHTING SYSTEM>STOP LIGHT SYSTEM .

  4. CHECK CURRENT DATA  .

    Using Subaru Select Monitor, display [P SW].

    Is "ON" displayed?

    Yes  : Go to  5 .

    No  :

    1. Check the "P range" switch. Ref. to CONTROL SYSTEMS>SHIFT LOCK SOLENOID AND P RANGE SWITCH>INSPECTION .
    2. Check the harness for "P range" switch lines. Ref. to WIRING SYSTEM>SHIFT LOCK CONTROL SYSTEM>WIRING DIAGRAM .
  5. CHECK SELECT CABLE INSTALLATION CONDITION  .

    Check that the select cable is installed properly.

    Is the select cable installed properly?

    Yes  : Go to  6 .

    No  : Confirm that the select cable is free from damage. If no damage is found, connect it again.

  6. CHECK SELECT LEVER OPERATION  .
    1. Disconnect the select cable from the transmission main body.
    2. Shift the select lever to another range.

    Can the select lever be shifted?

    Yes  : Repair the transmission body.

    CVT (TR580) model:  Ref. to CONTINUOUSLY VARIABLE TRANSMISSION (TR580)>TRANSMISSION ASSEMBLY>REMOVAL .

    CVT (TR690) model:  Ref. to CONTINUOUSLY VARIABLE TRANSMISSION (TR690)>TRANSMISSION ASSEMBLY>REMOVAL .

    No  : Go to  7 .

  7. CHECK SELECT LEVER OPERATION  .
    1. Disconnect the select cable from the select lever.
    2. Connect all harnesses.
    3. Shift the select lever to another range.

    Can the select lever be shifted?

    Yes  : Replace the select cable.

    No  :

    1. Check the select lever main body and replace it if defective.
    2. If there is no defect in the select lever main body, replace the keyless access control module. Ref. to SECURITY AND LOCKS>KEYLESS ACCESS CONTROL MODULE .
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.