Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Cylinder Block: Removal
- Remove the engine from the vehicle. Ref. to MECHANICAL (H4DOTC)>ENGINE ASSEMBLY>REMOVAL .
- Remove the crankshaft position sensor plate with drive plate. Ref. to CONTINUOUSLY VARIABLE TRANSMISSION (TR690)>DRIVE PLATE>REMOVAL .
- Remove the cylinder head. Ref. to MECHANICAL (H4DOTC)>CYLINDER HEAD>REMOVAL .
- Remove the oil pan upper. Ref. to LUBRICATION (H4DOTC)>OIL PAN>REMOVAL>OIL PAN UPPER .
- Remove the scavenge pump. Ref. to LUBRICATION (H4DOTC)>SCAVENGE PUMP>REMOVAL .
- Remove the water tank pipe assembly. Ref. to COOLING (H4DOTC)>WATER PIPE>REMOVAL>WATER TANK PIPE ASSEMBLY .
- Remove the PCV pipe assembly. Ref. to EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) (H4DOTC)>PCV PIPE>REMOVAL .
- Remove the knock sensor. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>KNOCK SENSOR>REMOVAL .
- Remove the PCV valve. Ref. to EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) (H4DOTC)>PCV VALVE>REMOVAL .
- Remove the engine rear hanger from cylinder block RH.
- Remove the bolts securing the crankshaft position sensor holder from the cylinder block LH, and remove the crankshaft position sensor with crankshaft position sensor holder.
- Set the part so that the cylinder block RH is on the upper side.
- Remove the #1 and #3 connecting rod caps and pistons from the cylinder block.NOTE: Mark each connecting rod cap and piston with a cylinder number.
- Using the ST, turn the crankshaft so that the #1 connecting rod cap (A) is located at the position shown in the figure.
Preparation tool:
ST: CRANKSHAFT SOCKET (18252AA000)
- Using the ST, loosen the #1 connecting rod cap bolt, and remove the #1 connecting rod cap bolt and #1 connecting rod cap.
Preparation tool:
ST: SOCKET (18270AA020)
- Using the ST, turn the crankshaft counterclockwise and separate the positions of the #1 pin (A) of crankshaft and the large end (B) of #1 connecting rod.
Preparation tool:
ST: CRANKSHAFT SOCKET (18252AA000)
- Push the #1 connecting rod in the direction of the arrow, and remove the #1 piston with #1 connecting rod from the cylinder block.
- Using the ST, turn the crankshaft so that the #3 connecting rod cap (A) is located at the position shown in the figure.
Preparation tool:
ST: CRANKSHAFT SOCKET (18252AA000)
- Using the ST, loosen the #3 connecting rod cap bolt, and remove the #3 connecting rod cap bolt and #3 connecting rod cap.
Preparation tool:
ST: SOCKET (18270AA020)
- Using the ST, turn the crankshaft counterclockwise and separate the positions of the #3 pin (A) of crankshaft and the large end (B) of #3 connecting rod.
Preparation tool:
ST: CRANKSHAFT SOCKET (18252AA000)
- Push the #3 connecting rod in the direction of the arrow, and remove the #3 piston with #3 connecting rod from the cylinder block.
- Using the ST, turn the crankshaft so that the #1 connecting rod cap (A) is located at the position shown in the figure.
- Set the part so that the cylinder block LH is on the upper side.
- Remove #2 and #4 connecting rod caps and pistons in the same removal procedure as #1 and #3 connecting rod caps and pistons.
- Set the part so that the cylinder block RH is on the upper side, and separate the cylinder block.
- Remove the engine stand from the cylinder block RH.
- Remove the bolt shown in the figure.
- Loosen the cylinder block mounting bolts in numerical order as shown in the figure, and then remove the bolts.
- While tapping the cylinder block RH with a plastic hammer, separate the cylinder block RH from the cylinder block LH.
NOTE: Lift the cylinder block RH gradually, and confirm that the crankshaft is remaining in the cylinder block LH. Lifting the cylinder block RH carelessly may cause the crankshaft to fall off. - Remove the engine stand from the cylinder block RH.
- Remove the crankshaft from cylinder block LH, and remove the rear oil seal.
- Remove the O-ring from the cylinder block LH.
- Remove the crankshaft bearings from the cylinder block.NOTE:
- Be careful not to confuse the crankshaft bearing combination.
- Press the bearing at the end opposite to locking lip (A).
- Remove the liquid gasket from cylinder block.
- Remove the cylinder block LH from the engine stand.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
