Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Auto Start Stop Indicator Does Not Illuminate Or Remains On
Detecting condition:
- Defective combination meter
- CAN communication is abnormal between TCM and the combination meter.
- Defective cockpit control module
- CHECK Auto Start Stop WARNING LIGHT (YELLOW)
.
- Turn the ignition switch to OFF.
- Check that the Auto Start Stop warning light (yellow) illuminates when the ignition switch is turned to ON. Ref. to AUTO START STOP (DIAGNOSTICS)>AUTO START STOP INDICATOR>CONDITION CHECK .
Does the Auto Start Stop warning light (yellow) illuminate?
Yes: Go to 2 .
No: Check the combination meter. Ref. to COMBINATION METER (DIAGNOSTICS)>ACTIVE TEST .
- CHECK Auto Start Stop WARNING LIGHT (YELLOW)
.
- Start the engine.
- Check that the Auto Start Stop warning light (yellow) goes off. Ref. to AUTO START STOP (DIAGNOSTICS)>AUTO START STOP INDICATOR>CONDITION CHECK .
Does the Auto Start Stop warning light (yellow) go off?
Yes: Go to 4 .
No: Go to 3 .
- CHECK DTC
.
- Turn the ignition switch to OFF.
- Start the engine.
- Read the DTC of [Auto Start Stop] using the Subaru Select Monitor. Ref. to AUTO START STOP (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is DTC displayed?
Yes: Perform the diagnosis according to the DTC. Ref. to AUTO START STOP (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)>LIST .
No: Check the combination meter. Ref. to COMBINATION METER (DIAGNOSTICS)>ACTIVE TEST .
- CHECK Auto Start Stop OFF INDICATOR
.
- Operate the Auto Start Stop cancel switch (center information display) to ON/OFF with engine idling.
- Check that the Auto Start Stop OFF indicator illuminates and goes off in turn every time the Auto Start Stop cancel switch (center information display) is turned to ON/OFF.
Does the Auto Start Stop OFF indicator illuminate and go off?
Yes: Go to 5 .
No: Go to 6 .
- CHECK Auto Start Stop INDICATOR (GREEN).
- Turn off the Auto Start Stop OFF indicator by operating the Auto Start Stop cancel switch (center information display).
- Start the engine.
- Perform the active test using Subaru Select Monitor to activate the Auto Start Stop. Ref. to AUTO START STOP (DIAGNOSTICS)>ACTIVE TEST .
Is the Auto Start Stop indicator (green) lit?
Yes: The circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.No: Check the combination meter. Ref. to COMBINATION METER (DIAGNOSTICS)>ACTIVE TEST .
- CHECK Auto Start Stop DEACTIVATION INDICATOR
.
- Turn off the Auto Start Stop OFF indicator by operating the Auto Start Stop cancel switch (center information display).
- Start the engine.
Is the Auto Start Stop deactivation indicator lit?
Yes: Go to 7 .
No: Check the combination meter. Ref. to COMBINATION METER (DIAGNOSTICS)>ACTIVE TEST .
- CHECK Auto Start Stop DEACTIVATION INDICATOR
.
Start to move the vehicle.
Does the Auto Start Stop deactivation indicator go off?
Yes: Go to 8 .
No: Check the combination meter. Ref. to COMBINATION METER (DIAGNOSTICS)>ACTIVE TEST .
- CHECK Auto Start Stop CANCEL SWITCH (CENTER INFORMATION DISPLAY)
.
- Turn the ignition switch to OFF.
- Start the engine.
- Using the Subaru Select Monitor, read the data of [Auto Start Stop OFF Switch] when the Auto Start Stop cancel switch (center information display) is operated to ON/OFF. Ref. to AUTO START STOP (DIAGNOSTICS)>DATA MONITOR .
Does the display of [Auto Start Stop OFF Switch] change?
Yes: Go to 10 .
No: Go to 9 .
- CHECK Auto Start Stop CANCEL SWITCH (CENTER INFORMATION DISPLAY)
.
Check the Auto Start Stop cancel switch (center information display). Ref. to COCKPIT CONTROL (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
Is the check result OK?
Yes: Go to 10 .
No: Replace the cockpit control module. Ref. to ENTERTAINMENT AND MONITORING>COCKPIT DISPLAY .
- CHECK COMBINATION METER
.
Check the combination meter. Ref. to COMBINATION METER (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
Is the check result OK?
Yes: Go to 11 .
No: Replace the combination meter. Ref. to INSTRUMENTATION/DRIVER INFO>COMBINATION METER .
- CHECK DTC
.
Using the Subaru Select Monitor, read all DTCs. Ref. to COMMON (DIAG)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is U-code displayed?
Yes: Perform the diagnosis according to the DTC. Ref. to LAN SYSTEM (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)>LIST .
No: Replace the combination meter. Ref. to INSTRUMENTATION/DRIVER INFO>COMBINATION METER .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
