Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure For Subaru Select Monitor Communication: Inspection
Trouble symptom:Â
Cannot communicate with [Driver Monitor].
Detecting condition:Â
- Defective harness connector
- Power supply circuit malfunction
- Driver Monitoring Unit malfunctioning
- Defective CAN communication circuit
- Defective Subaru Select Monitor
Wiring diagram:Â
- Driver monitoring system Ref. to WIRING SYSTEM>DRIVER MONITORING SYSTEM>WIRING DIAGRAM .
- CAN communication system Ref. to WIRING SYSTEM>CAN COMMUNICATION SYSTEM>WIRING DIAGRAM .
- CHECK IGNITION SWITCHÂ
.
Check the ignition switch.
Is the ignition switch ON?
Yes : Go to  2 .
No : Turn the ignition switch to ON, and select the [Driver Monitor] using the Subaru Select Monitor.
- CHECK BATTERYÂ
.
- Turn the ignition switch to OFF.
- Check the battery. Ref. to STARTING/CHARGING SYSTEMS (H4DOTC)>BATTERY>INSPECTION
. Ref. to STARTING/CHARGING SYSTEMS (H4DO)>BATTERY>INSPECTION
.
Is the check result OK?
Yes : Go to  3 .
No : Charge or replace the battery.
- CHECK INSTALLATION OF Driver Monitoring Unit CONNECTORÂ
.
Check the Driver Monitoring Unit connector.
Is the Driver Monitoring Unit connector inserted into the Driver Monitoring Unit until it locks?
Yes : Go to  4 .
No : Insert the Driver Monitoring Unit connector into the Driver Monitoring Unit until it is locked.
- CHECK LAN SYSTEMÂ
.
Perform the diagnosis for LAN system. Ref. to LAN SYSTEM (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
Is there any fault in LAN system?
Yes : Perform the inspection according to the diagnosis for LAN system.
No : Go to  5 .
- CHECK SUBARU SELECT MONITOR COMMUNICATIONÂ
.
- Turn the ignition switch to ON.
- Check whether communication to the Driver Monitoring Unit can be executed normally.
Is communication with [Driver Monitor] possible?
Yes : Read the DTC of [Driver Monitor] using the Subaru Select Monitor. Ref. to Driver Monitor (Diagnostics)>Diagnostic Trouble Code (DTC) .
No : Go to  6 .
- CHECK SUBARU SELECT MONITORÂ
.
Connect the Subaru Select Monitor to another vehicle to verify that the communication for initializing can be executed normally.
Is communication for initializing possible?
Yes : Go to  7 .
No : Repair or replace the Subaru Select Monitor.
- CHECK Driver Monitoring Unit POWER SUPPLY CIRCUIT (OPEN • SHORT CIRCUIT)Â
.
- Turn the ignition switch to OFF.
- Disconnect the Driver Monitoring Unit connector.
- Using a tester, measure the voltage between Driver Monitoring Unit connector and chassis ground.
Connector & terminalÂ
(i87) No. 8 (+) - Chassis ground (-):
Is the voltage 10 - 15 V?
Yes : Go to  8 .
No : Repair the open or short circuit of harness or the poor contact of connector between the Driver Monitoring Unit connector and the battery.
- CHECK Driver Monitoring Unit GROUND CIRCUIT (OPEN)Â
.
- Turn the ignition switch to OFF.
- Measure the resistance between Driver Monitoring Unit connector and chassis ground.
Connector & terminalÂ
(i87) No. 6 - Chassis ground:
Is the resistance less than 10 Ω?
Yes : Go to  9 .
No : Repair the open circuit of Driver Monitoring Unit ground circuit or poor contact of connector.
- CHECK POOR CONTACT OF CONNECTORÂ
.
Check Driver Monitoring Unit power supply, ground circuit and data link connector for poor contact.
Is there poor contact?
Yes : Repair the poor contact.
No : Replace Driver Monitoring Unit. Ref. to INSTRUMENTATION/DRIVER INFO>DRIVER MONITORING UNIT .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
