Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Subaru Outback BaseFACTORY OEM SERVICE PROCEDURE
Inspection Mode 7
| DTC | Description and trouble part | Note |
|---|---|---|
| B1017 | COLLISION DETECTION SIGNAL INPUT | - |
| B1107 | CAN COMMUNICATION (BIU) STUCK | - |
| B1402 | IMMOBILIZER KEY COLLATION | Models without the keyless access with push button start system, and except for C0 and C5 |
| B1403 | IMMOBILIZER SUB CONTROL MODULE COLLATION | Models without the keyless access with push button start system, and except for C0 and C5 |
| B1404 | IMMOBILIZER SUB CONTROL MODULE COMMUNICATION | Models without the keyless access with push button start system, and except for C0 and C5 |
| B140A | IMMOBILIZER SUB CONTROL MODULE NON-VOLATILE MEMORY | Models without the keyless access with push button start system, and except for C0 and C5 |
| B1410 | TRANSPONDER COMMUNICATION | Models without the keyless access with push button start system, and except for C0 and C5 |
| B1411 | IMMOBILIZER ANTENNA | Models without the keyless access with push button start system, and except for C0 and C5 |
| U0074 | CONTROL MODULE COMMUNICATION BUS "BODY-CAN" OFF | - |
| U0100 | LOST COMMUNICATION WITH ECM/PCM "A" | - |
| U0122 | LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE | - |
| U0127 | LOST COMMUNICATION WITH TIRE PRESSURE MONITOR CONTROL MODULE AND/OR KEYLESS ENTRY CONTROL MODULE | - |
| U0141 | LOST COMMUNICATION WITH BODY CONTROL MODULE "A" | - |
| U0155 | LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULE | - |
| U0167 | LOST COMMUNICATION WITH IMMOBILIZER CONTROL MODULE | Model with immobilizer control module |
| U0327 | SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE | - |
| U0401 | INVALID DATA RECEIVED FROM ECM/PCM "A" | - |
| U0416 | INVALID DATA RECEIVED FROM VEHICLE DYNAMICS CONTROL MODULE | - |
| U0423 | INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL MODULE | - |
| U0426 | INVALID DATA RECEIVED FROM IMMOBILIZER CONTROL MODULE | Model with immobilizer control module |
| U0427 | INVALID DATA RECEIVED FROM VEHICLE SECURITY CONTROL MODULE | - |
| U0430 | INVALID DATA RECEIVED FROM TIRE PRESSURE MONITOR CONTROL MODULE AND/OR KEYLESS ENTRY CONTROL MODULE | - |
| U0431 | INVALID DATA RECEIVED FROM BODY CONTROL MODULE "A" | - |
Diagnostic procedure:
- Using the Subaru Select Monitor, perform the clear memory of [Body Control]. Ref. to COMMON (DIAG)>CLEAR MEMORY .
- Using the Subaru Select Monitor, read the DTC of [Body Control] to check that there is no DTC displayed. Ref. to Body Control (Diagnostics)>Diagnostic Trouble Code (DTC)Β .NOTE: If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs. After solving the DTC, repeat from step 1).
- Turn the ignition switch OFF β ON, and wait for 10 seconds or more.
- Using the Subaru Select Monitor, read the DTC of [Body Control] to check that there is no DTC displayed. Ref. to Body Control (Diagnostics)>Diagnostic Trouble Code (DTC)Β .NOTE: If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
