Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Subaru Outback BaseFACTORY OEM SERVICE PROCEDURE
Inspection Mode 1
| DTC | Description and trouble part | Note |
|---|---|---|
| B2D00 | CAMERA ECU INTERNAL FAILURE | - |
| B2D01 | FRONT CAMERA WIRING HARNESS OPEN CIRCUIT OR TROUBLE (POWER) | - |
| B2D03 | REAR CAMERA WIRING HARNESS OPEN CIRCUIT OR TROUBLE (POWER) | - |
| B2D04 | FRONT CAMERA WIRING HARNESS OPEN CIRCUIT OR TROUBLE (IMAGE) | - |
| B2D06 | REAR CAMERA WIRING HARNESS OPEN CIRCUIT OR TROUBLE (IMAGE) | - |
| B2D07 | CAMERA ECU LOW VOLTAGE (LESS THAN 9V) | - |
| B2D08 | CAMERA ECU HIGH VOLTAGE (MORE THAN 16V) | - |
| U007A | CONTROL MODULE COMMUNICATION BUS "H" OFF | - |
| U0101 | LOST COMMUNICATION WITH TCM | - |
| U0122 | LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE | - |
| U0128 | LOST COMMUNICATION WITH PARK BRAKE CONTROL MODULE | - |
| U0155 | LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULE | - |
| U0162 | LOST COMMUNICATION WITH AUDIO VISUAL NAVIGATION DISPLAY MODULE | - |
| U0402 | INVALID DATA RECEIVED FROM TCM | - |
| U0416 | INVALID DATA RECEIVED FROM VEHICLE DYNAMICS CONTROL MODULE | - |
| U0417 | INVALID DATA RECEIVED FROM PARK BRAKE CONTROL MODULE | - |
| U0423 | INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL MODULE | - |
| U0463 | INVALID DATA RECEIVED FROM NAVIGATION DISPLAY MODULE | - |
| U1120 | LOST COMMUNICATION WITH AUTOSTART STOP CONTROL MODULE | - |
| U114C | LOST COMMUNICATION WITH GATEWAY "A" SA-BUS | - |
| U1232 | LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE | - |
| U1283 | LOST COMMUNICATION WITH EYESIGHT SA-BUS | - |
| U144D | INVALID DATA RECEIVED FROM GATEWAY "A" SA-BUS | - |
| U1469 | INVALID DATA RECEIVED FROM AUTOSTART STOP CONTROL MODULE | - |
| U1533 | INVALID DATA RECEIVED FROM REAR/SIDE RADAR CONTROL MODULE | - |
| U1584 | INVALID DATA RECEIVED FROM EYESIGHT SA-BUS | - |
Diagnostic procedure:
- Using the Subaru Select Monitor, perform the clear memory of [Multi View Monitor] Ref. to COMMON (DIAG)>CLEAR MEMORY .
- Using the Subaru Select Monitor, read the DTC of [Multi View Monitor] to check that there is no DTC displayed Ref. to MULTI VIEW MONITOR (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)Β NOTE: If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs. After solving the DTC, repeat from step 1).
- After the ignition switch is ON, wait for one minute or more.
- Using the Subaru Select Monitor, read the DTC of [Multi View Monitor] to check that there is no DTC displayed Ref. to MULTI VIEW MONITOR (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)Β NOTE: If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
