Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Brake Warning Light Does Not Go Off
Detecting condition:Â
- Brake warning light circuit is shorted.
- Defective sensor/connector
- Defective CAN communication
Trouble symptom:Â
Brake warning light does not go off after starting the engine.
Wiring diagram:Â
Parking brake/brake fluid level warning light system Ref. to WIRING SYSTEM>PARKING BRAKE/BRAKE FLUID LEVEL WARNING LIGHT SYSTEM .
Combination meter system Ref. to WIRING SYSTEM>COMBINATION METER SYSTEM .
- CHECK INSTALLATION OF VDCCM&H/U CONNECTORÂ
.
- Turn the ignition switch to OFF.
- Check that the VDCCM&H/U connector is inserted until it is locked by clamp.
Is the connector firmly inserted?
Yes : Go to  2 .
No : Insert the VDCCM&H/U connector until it is locked by clamp.
- READ DTCÂ
.
Read the DTC using Subaru Select Monitor. Ref. to BRAKE CONTROL (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)Â .
Is DTC displayed?
Yes : Perform the diagnosis according to DTC. Ref. to BRAKE CONTROL (DIAGNOSTICS)>Diagnostic Trouble Code (DTC)>LIST .
No : Go to  3 .
- CHECK LAN SYSTEMÂ
.
Check the LAN system. Ref. to LAN SYSTEM (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
Is the check result OK?
Yes : Go to  4 .
No : Perform the diagnosis for LAN system.
- CHECK BRAKE FLUID AMOUNTÂ
.
Check the amount of brake fluid in the reservoir tank of master cylinder.
Does the level of the brake fluid amount fall between the lines of "MAX" and "MIN"?
Yes : Go to  5 .
No : Replenish brake fluid to the specified value.
- CHECK BRAKE FLUID LEVEL SWITCHÂ
.
- Turn the ignition switch to OFF.
- Disconnect the level switch connector (B16) from master cylinder.
- Measure the resistance of master cylinder terminals.
TerminalsÂ
No. 1 - No. 2:
Is the resistance 1 MΩ or more?
Yes : Go to  6 .
No : Replace the master cylinder. Ref. to BRAKE>MASTER CYLINDER .
- CHECK GROUND SHORT OF HARNESSÂ
.
- Disconnect the connector from VDCCM.
- Measure the resistance between VDCCM connector and chassis ground.
Connector and terminalÂ
(B310) No. 27 - Chassis ground:
Is the resistance 1 MΩ or more?
Yes : Go to  7 .
No : Repair the harness between VDCCM and brake fluid level switch.
- CHECK COMBINATION METERÂ
.
Check the combination meter. Ref. to INSTRUMENTATION/DRIVER INFO>COMBINATION METER SYSTEM>OPERATION>SELF-DIAGNOSIS DISPLAY MODE .
Is the check result OK?
Yes : Replace the VDCCM&H/U. Ref. to VEHICLE DYNAMICS CONTROL (VDC)>VDC CONTROL MODULE AND HYDRAULIC CONTROL UNIT (VDCCM&H/U) .
No : Replace the combination meter. Ref. to INSTRUMENTATION/DRIVER INFO>COMBINATION METER .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
