Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Subaru Crosstrek HybridFACTORY OEM SERVICE PROCEDURE
Inspection Mode Ai
| DTC | Description and trouble part | Condition | Number of driving cycles on the detecting condition |
|---|---|---|---|
| P0030 | A/F/O2 HEATER CONTROL CIRCUIT BANK 1 SENSOR 1 | - | 2 |
| P0087 | FUEL RAIL/SYSTEM PRESSURE - TOO LOW BANK 1 | - | 1 |
| P0088 | FUEL RAIL/SYSTEM PRESSURE - TOO HIGH BANK 1 | - | 1 |
| P0125 | INSUFFICIENT COOLANT TEMPERATURE FOR CLOSED LOOP FUEL CONTROL | [Engine Coolant Temperature] at engine starting: Less than -15°C (5°F) | 2 |
| P0128 | COOLANT THERMOSTAT (COOLANT TEMPERATURE BELOW THERMOSTAT REGULATING TEMPERATURE) | - | 2 |
| P013A | O2 SENSOR SLOW RESPONSE - RICH TO LEAN BANK 1 SENSOR 2 | - | 2 |
| P013E | O2 SENSOR DELAYED RESPONSE - RICH TO LEAN BANK 1 SENSOR 2 | - | 2 |
| P0141 O2 | SENSOR HEATER CIRCUIT BANK 1 SENSOR 2 | - | 2 |
| P0171 | SYSTEM TOO LEAN BANK 1 | - | 2 |
| P0172 | SYSTEM TOO RICH BANK 1 | - | 2 |
| P0300 | RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED | - | 2 |
| P0301 | CYLINDER 1 MISFIRE DETECTED | - | 2 |
| P0302 | CYLINDER 2 MISFIRE DETECTED | - | 2 |
| P0303 | CYLINDER 3 MISFIRE DETECTED | - | 2 |
| P0304 | CYLINDER 4 MISFIRE DETECTED | - | 2 |
| P0506 | IDLE CONTROL SYSTEM RPM - LOWER THAN EXPECTED | - | 2 |
| P0507 | IDLE CONTROL SYSTEM RPM - HIGHER THAN EXPECTED | - | 2 |
| P2096 | POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1 | - | 2 |
| P2097 | POST CATALYST FUEL TRIM SYSTEM TOO RICH BANK 1 | - | 2 |
| P2195 | A/F/O2 SENSOR SIGNAL BIASED/STUCK LEAN BANK 1 SENSOR 1 | - | 2 |
| P2196 | A/F/O2 SENSOR SIGNAL BIASED/STUCK RICH BANK 1 SENSOR 1 | - | 2 |
| P2271 | O2 SENSOR SIGNAL BIASED/STUCK RICH BANK 1 SENSOR 2 | - | 2 |
WARNING:
When performing inspection mode AI on a public road, pay sufficient attention to the traffic condition and give the highest priority to safe driving.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.