Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure for Subaru Select Monitor Communication: Inspection
Trouble symptom:Â
Cannot communicate with [Multi-Function Display].
Detecting condition:Â
- Defective harness connector
- Power supply circuit malfunction
- Defective MFD
- Defective CAN communication circuit
- Defective Subaru Select Monitor
Wiring diagram:Â
- Multi-function display (MFD) system Ref. to WIRING SYSTEM>Multi-function Display (MFD) System>WIRING DIAGRAM .
- CAN communication system Ref. to WIRING SYSTEM>CAN Communication System>WIRING DIAGRAM .
- CHECK IGNITION SWITCHÂ
.
Check the ignition switch.
Is the ignition switch ON?
Yes : Go to  2.
No : Turn the ignition switch to ON, and select the [Multi-Function Display] using the Subaru Select Monitor.
- CHECK BATTERYÂ
.
- Turn the ignition switch to OFF.
- Check the battery. Ref. to STARTING/CHARGING SYSTEMS (H4DOTC)>Battery>INSPECTION .
Is the check result OK?
Yes : Go to  3.
No : Charge or replace the battery.
- CHECK INSTALLATION OF MFD CONNECTORÂ
.
Check the MFD connector.
Is the MFD connector inserted into the MFD until it locks?
Yes : Go to  4.
No : Be sure to insert the MFD connector into the MFD until it is locked.
- CHECK LAN SYSTEMÂ
.
Perform the diagnosis for LAN system. Ref. to LAN SYSTEM (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
Is there any fault in LAN system?
Yes : Perform the inspection according to the diagnosis for LAN system.
No : Go to  5.
- CHECK SUBARU SELECT MONITOR COMMUNICATIONÂ
.
- Turn the ignition switch to ON.
- Check whether communication to MFD can be executed normally.
Is communication with [Multi-function Display] possible?
Yes : Read the DTC of [Multi-Function Display] using the Subaru Select Monitor. Ref. to MULTI-FUNCTION DISPLAY (DIAGNOSTICS)>Diagnostic Trouble Code (DTC) .
No : Go to  6.
- CHECK SUBARU SELECT MONITORÂ
.
Connect the Subaru Select Monitor to another vehicle to verify that the communication for initializing can be executed normally.
Is communication for initializing possible?
Yes : Go to  7.
No : Repair or replace the Subaru Select Monitor.
- CHECK MFD POWER SUPPLY CIRCUIT (OPEN OR SHORT CIRCUIT)Â
.
- Turn the ignition switch to OFF.
- Disconnect the MFD connector.
- Turn the ignition switch to ON.
- Using a tester, measure the voltage between the MFD connector and chassis ground.
Connector & terminalÂ
(i122) No. 23 (+) - Chassis ground (-):
(i122) No. 24 (+) - Chassis ground (-):
Is the voltage 10 - 15 V?
Yes : Go to  8.
No : Repair the open or short circuit of harness, or poor contact of connector.
- CHECK MFD GROUND CIRCUIT (OPEN)Â
.
- Turn the ignition switch to OFF.
- Measure the resistance between MFD connector and chassis ground.
Connector & terminalÂ
(i122) No. 21 - Chassis ground:
Is the resistance less than 10 Ω?
Yes : Go to  9.
No : Repair the open circuit of the MFD ground circuit or poor contact of connector.
- CHECK POOR CONTACT OF CONNECTORÂ
.
Check MFD power supply, ground circuit and data link connector for poor contact.
Is there poor contact?
Yes : Repair the poor contact.
No : Replace the MFD. Ref. to INSTRUMENTATION/DRIVER INFO>MULTI-FUNCTION DISPLAY (MFD) .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
