2020 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE

Basic Diagnostic Procedure: Procedure: Engine

WARNING: This page is about a different variant/trim than selected.
  1. CHECK ENGINE START FAILURE. 
    1. Ask the customer when and how the trouble occurred using the interview check list. Refer to ENGINE (DIAGNOSTICS) (STI)>CHECK LIST FOR INTERVIEW>CHECK .
    2. Start the engine.

      Does the engine start?

      Yes:  Go to  2.

      No:  Inspection using "Diagnostics for Engine Starting Failure". Refer to ENGINE (DIAGNOSTICS) (STI)>DIAGNOSTICS FOR ENGINE STARTING FAILURE .

  2. CHECK ILLUMINATION OF MALFUNCTION INDICATOR LIGHT. 

    Check the lighting condition of the malfunction indicator light.

    Does the malfunction indicator light illuminate?

    Yes:  Go to  3.

    No:  Inspection using "General Diagnostic Table". Refer to ENGINE (DIAGNOSTICS) (STI)>GENERAL DIAGNOSTIC TABLE .

  3. CHECK COMMUNICATION STATUS. 
    1. Turn the ignition switch to OFF.
    2. Connect the Subaru Select Monitor or general scan tool to the data link connector.
    3. Turn the ignition switch to ON, and run the Subaru Select Monitor or general scan tool.
      NOTE:
      • Subaru Select Monitor

        For detailed operation procedures, refer to the "Subaru Select Monitor". Refer to ENGINE (DIAGNOSTICS) (STI)>SUBARU SELECT MONITOR .

      • General scan tool

        For detailed operation procedures, refer to the general scan tool operation manual.

      Does Subaru Select Monitor or general scan tool communicate with vehicle normally?

      Yes:  Go to  4.

      No:  Inspection using "Diagnostic Procedure for Subaru Select Monitor Communication". Refer to ENGINE (DIAGNOSTICS) (STI)>DIAGNOSTIC PROCEDURE FOR SUBARU SELECT MONITOR COMMUNICATION .

  4. CHECK DTC. 

    Read DTC using Subaru Select Monitor or general scan tool.

    NOTE:

    Is DTC displayed on Subaru Select Monitor or general scan tool?

    Yes:  Record DTC and freeze frame data, then repair the trouble cause. Refer to ENGINE (DIAGNOSTICS) (STI)>LIST OF DIAGNOSTIC TROUBLE CODE (DTC) . after repair, go to the next step. Go to  5.

    No:  Repair the related parts.

    NOTE: If DTC is not shown on display although the malfunction indicator light illuminates, perform the diagnosis of malfunction indicator light circuit or combination meter. Refer to ENGINE (DIAGNOSTICS) (STI)>MALFUNCTION INDICATOR LIGHT .
  5. PERFORM DIAGNOSIS. 
    1. Perform the Clear Memory Mode. Refer to ENGINE (DIAGNOSTICS) (STI)>CLEAR MEMORY MODE .
    2. Perform the Inspection Mode or Drive Cycle. Refer to ENGINE (DIAGNOSTICS) (STI)>INSPECTION MODE . Refer to ENGINE (DIAGNOSTICS) (STI)>DRIVE CYCLE .

      Is DTC displayed on Subaru Select Monitor or general scan tool?

      Yes:  Inspect using "Diagnostic Procedure with Diagnostic Trouble Code (DTC)". Refer to ENGINE (DIAGNOSTICS) (STI)>DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC) .

      No:  Finish the diagnosis.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.