Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fuel Pump Circuit
Wiring diagram:Â
Engine Electrical System Refer to WIRING SYSTEM>ENGINE ELECTRICAL SYSTEM .
- CHECK OPERATING SOUND OF FUEL PUMPÂ
.
Check if the fuel pump operates for two seconds when turning the ignition switch to ON.
NOTE: Fuel pump operation can be executed using the Subaru Select Monitor. Refer to "Active Test" for the procedures. Refer to ENGINE (DIAGNOSTICS) (H4DO)>ACTIVE TEST .Does the fuel pump emit operating sound?
Yes : Check the fuel injector circuit. Refer to ENGINE (DIAGNOSTICS) (H4DO)>DIAGNOSTICS WITH PHENOMENON>FUEL INJECTOR CIRCUIT .
No : Go to  2.
- CHECK GROUND CIRCUIT OF FUEL PUMP (OPEN CIRCUIT)Â
.
- Turn the ignition switch to OFF.
- Disconnect the connector from fuel pump.
- Measure the resistance of harness between fuel pump connector and chassis ground.
Connector & terminalÂ
(R132) No. 6 - Chassis ground:
Is the resistance less than 5 Ω?
Yes : Go to  3.
No : Repair the following item.
- Open circuit in harness between fuel pump connector and chassis ground
- Poor contact of J/C
- CHECK POWER SUPPLY TO FUEL PUMPÂ
.
- Turn the ignition switch to ON.
- Measure the voltage between fuel pump connector and chassis ground.
Connector & terminalÂ
(R132) No. 5 (+) - Chassis ground (-):
Is the voltage 10 V or more?
Yes : Replace the fuel pump. Refer to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>FUEL PUMP ASSEMBLY .
No : Go to  4.
- CHECK HARNESS BETWEEN FUEL PUMP AND FUEL PUMP RELAY (OPEN)Â
.
- Turn the ignition switch to OFF.
- Remove the fuel pump relay.
- Measure the resistance of harness between fuel pump connector and fuel pump relay connector.
Connector & terminalÂ
(R132) No. 5 - M/B (fuel pump relay) No. 3:
Is the resistance less than 1 Ω?
Yes : Go to  5.
No : Repair the following item.
- Open circuit in harness between fuel pump connector and fuel pump relay connector
- Poor contact of coupling connector
- CHECK HARNESS BETWEEN FUEL PUMP AND FUEL PUMP RELAY (SHORT TO GROUND)Â
.
Measure the resistance between fuel pump connector and chassis ground.
Connector & terminalÂ
(R132) No. 5 - Chassis ground:
Is the resistance 1 MΩ or more?
Yes : Go to  6.
No : Repair the short circuit to ground in harness between fuel pump connector and fuel pump relay connector.
- CHECK FUEL PUMP RELAYÂ
.
Check the fuel pump relay. Refer to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>FUEL PUMP RELAY .
Is the check result OK?
Yes : Go to  7.
No : Replace the fuel pump relay. Refer to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>FUEL PUMP RELAY .
- CHECK HARNESS BETWEEN ECM AND FUEL PUMP RELAY (OPEN)Â
.
- Disconnect the connector from ECM.
- Measure the resistance of harness between ECM connector and fuel pump relay connector.
Connector & terminalÂ
(B62) No. 31 - M/B (fuel pump relay) No. 4:
Is the resistance less than 1 Ω?
Yes : Go to  8.
No : Repair the open circuit of harness between ECM connector and fuel pump relay connector.
- CHECK POWER SUPPLY OF FUEL PUMP RELAYÂ
.
- Turn the ignition switch to ON.
- Measure the voltage between fuel pump relay connector and chassis ground.
Connector & terminalÂ
M/B (fuel pump relay) No. 1 (+) - Chassis ground (-):
M/B (fuel pump relay) No. 2 (+) - Chassis ground (-):
Is the voltage 10 V or more?
Yes : Repair the poor contact of ECM connector.
No : Repair the open or ground short in the harness of power supply circuit.
NOTE: After the faulty parts are repaired or replaced, perform the final check in Basic Diagnostic Procedure. Refer to ENGINE (Diagnostics) (H4DO)>Basic Diagnostic Procedure>PROCEDURE .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
