Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Model Without Push Button Start
- After servicing or replacing faulty parts, perform Clear Memory Mode. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>CLEAR MEMORY MODE>OPERATIONÂ ., and inspection mode. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>INSPECTION MODE>PROCEDUREÂ .
- Use the check board when measuring the ECM terminal voltage and resistance.
Wiring diagram:Â
Engine Electrical System. Ref. to WIRING SYSTEM>ENGINE ELECTRICAL SYSTEM>WIRING DIAGRAM .
- CHECK BATTERYÂ
.
Check the battery. Ref. to STARTING/CHARGING SYSTEMS (H4DO)>BATTERY .
Is the check result OK?
YesÂ
Go to  2 .
NoÂ
Charge or replace the battery. Ref. to STARTING/CHARGING SYSTEMS (H4DO)>BATTERY .
- CHECK OPERATION OF STARTER MOTORÂ
.
Check the starter motor operation.
Does the starter motor operate?
YesÂ
Go to  3 .
NoÂ
Go to  4 .
- CHECK DTCÂ
.
Read the engine DTC using the Subaru Select Monitor or general scan tool. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>READ DIAGNOSTIC TROUBLE CODE (DTC)Â .
Are any DTCs displayed? (Current malfunction). Ref. to ENGINE (DIAGNOSTICS) (H4DO)>READ DIAGNOSTIC TROUBLE CODE (DTC)>OPERATIONÂ .
YesÂ
Check the appropriate DTC using the "List of Diagnostic Trouble Code (DTC)". Ref. to ENGINE (DIAGNOSTICS) (H4DO)>LIST OF DIAGNOSTIC TROUBLE CODEÂ
NoÂ
Check ignition control system. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>DIAGNOSTICS FOR ENGINE STARTING FAILURE>IGNITION CONTROL SYSTEMÂ .
- CHECK INPUT SIGNAL FOR STARTER MOTORÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from starter motor.
- Turn the ignition switch to START.
- Measure the voltage between the starter motor connector and the engine ground.
Connector & terminalÂ
(B14) No. 1 (+) - Engine ground (-):
NOTE: Place the select lever in "P" range or "N" range.Is the voltage 10 V or more?
YesÂ
Check the starter motor. Ref. to STARTING/CHARGING SYSTEMS (H4DO)>STARTER .
NoÂ
Go to  5 .
- CHECK HARNESS BETWEEN BATTERY AND IGNITION SWITCH CONNECTORÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from ignition switch.
- Measure the power supply voltage between ignition switch connector and chassis ground.
Connector & terminalÂ
(i58) No. 4 (+) - Chassis ground (-):
(B159) No. 2 (+) - Chassis ground (-):
(i136) No. 38 (+) - Chassis ground (-):
(i58) No. 5 (+) - Chassis ground (-):
Is the voltage 10 V or more?
YesÂ
Go to  6 .
NoÂ
Check the harnesses and connectors, and repair or replace them if necessary.
NOTE: In this case, repair the following item:- Open circuit of harness between battery and ignition switch connector
- Blown out of fuse
- Replacement of F/B
- CHECK IGNITION SWITCHÂ
.
Measure the resistance between ignition switch terminals after turning the ignition switch to
START position.
TerminalsÂ
No. 4 - No. 3:
No. 5 - No. 7:
Is the resistance less than 1 Ω?
YesÂ
Go to  7 .
NoÂ
Replace the ignition switch. Ref. to SECURITY AND LOCKS>IGNITION KEY LOCK>REPLACEMENT .
- CHECK INPUT VOLTAGE OF STARTER RELAYÂ
.
- Turn the ignition switch to OFF.
- Remove the starter relay.
- Connect the connector to ignition switch.
- Turn the ignition switch to START position, and measure the voltage between F/B (starter relay) connector and chassis ground.
Connector & terminalÂ
(i137) No. 8 (+) - Chassis ground (-):
(i137) No. 10 (+) - Chassis ground (-):
Is the voltage 10 V or more?
YesÂ
Go to  8 .
NoÂ
Check the following item and repair if necessary.
- Blown out of fuse
- Open circuit or short circuit to ground in harness between F/B (starter relay) and ignition switch connector
- CHECK STARTER RELAYÂ
.
Check the starter relay. Ref. to STARTING/CHARGING SYSTEMS (H4DO)>STARTER RELAY .
Is the check result OK?
YesÂ
Go to  9 .
NoÂ
Replace the F/B (starter relay).
- CHECK VOLTAGE OF F/B (STARTER RELAY) CONNECTORÂ
.
- Turn the ignition switch to START.
- Measure the voltage between F/B (starter relay) connector and chassis ground.
Connector & terminalÂ
(B159) No. 4 (+) - Chassis ground (-):
NOTE: Place the select lever in "P" range or "N" range.Is the voltage 10 V or more?
YesÂ
Go to  10 .
NoÂ
Replace the F/B.
- CHECK HARNESS BETWEEN ECM AND STARTER RELAY CONNECTORÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from ECM.
- Measure the resistance of harness between ECM connector and F/B (starter relay) connector.
Connector & terminalÂ
(B134) No. 62 - (B158) No. 2:
Is the resistance less than 1 Ω?
YesÂ
Go to  11 .
NoÂ
Repair the open circuit of harness between ECM connector and starter relay connector.
- CHECK HARNESS BETWEEN STARTER RELAY AND INHIBITOR SWITCH CONNECTORÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from inhibitor switch.
- Measure the resistance of harness between F/B (starter relay) connector and inhibitor switch connector.
Connector & terminalÂ
(B159) No. 4 - (T7) No. 6:
Is the resistance less than 1 Ω?
YesÂ
Go to  12 .
NoÂ
Repair the harness and connector.
NOTE: In this case, repair the following item:- Open circuit in harness between F/B (starter relay) connector and inhibitor switch connector
- Poor contact of coupling connector
- CHECK HARNESS BETWEEN INHIBITOR SWITCH AND STARTER MOTORÂ
.
Measure the resistance of harness between the inhibitor switch connector and starter motor.
Connector & terminalÂ
(T7) No. 9 - (B14) No. 1:
Is the resistance less than 1 Ω?
YesÂ
Go to  13 .
NoÂ
Repair the harness and connector.
NOTE: In this case, repair the following item:- Open circuit in harness between inhibitor switch connector and starter motor
- Poor contact of coupling connector
- CHECK INHIBITOR SWITCHÂ
.
- Place the select lever in "P" range and "N" range.
- Measure the resistance between inhibitor switch terminals.
TerminalsÂ
No. 6 - No. 9:
Is the resistance less than 1 Ω?
Check the engine control module (ECM) power supply and ground line. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>DIAGNOSTICS FOR ENGINE STARTING FAILURE>CHECK POWER SUPPLY AND GROUND LINE OF ENGINE CONTROL MODULE (ECM)Â .
Replace the inhibitor switch. Ref. to CONTINUOUSLY VARIABLE TRANSMISSION(TR580)>INHIBITOR SWITCH .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
