Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fuel Injector Circuit
- Check or repair only faulty parts.
- After servicing or replacing faulty parts, perform Clear Memory Mode. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>CLEAR MEMORY MODE>OPERATIONÂ ., and inspection mode. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>INSPECTION MODE>PROCEDUREÂ .
- Use the check board when measuring the ECM terminal voltage and resistance.
Wiring diagram:Â
Engine Electrical System. Ref. to WIRING SYSTEM>ENGINE ELECTRICAL SYSTEM>WIRING DIAGRAM .
- CHECK OPERATION OF EACH FUEL INJECTORÂ
.
While cranking the engine, check each fuel injector emits operating sound. Use a sound scope or attach a screwdriver to the injector to listen to sounds for this check.
Does the fuel injector emit operating sound?
YesÂ
Check the fuel pressure. Ref. to MECHANICAL(H4DO)>FUEL PRESSURE>INSPECTION .
NoÂ
Go to  2 .
- CHECK POWER SUPPLY TO EACH FUEL INJECTORÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from fuel injector.
- Turn the ignition switch to ON.
- Measure the power supply voltage between fuel injector terminal and engine ground.
Connector & terminalÂ
#1 (E5) No. 2 (+) - Engine ground (-):
#2 (E16) No. 2 (+) - Engine ground (-):
#3 (E6) No. 2 (+) - Engine ground (-):
#4 (E17) No. 2 (+) - Engine ground (-):
Is the voltage 10 V or more?
YesÂ
Go to  3 .
NoÂ
Repair the harness and connector.
NOTE: In this case, repair the following item:- Open circuit in harness between main relay connector and fuel injector connector
- Poor contact of main relay connector
- Poor contact of coupling connector
- CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTORÂ
.
- Turn the ignition switch to OFF.
- Disconnect the connector from ECM.
- Measure the resistance of harness between ECM connector and fuel injector connector.
Connector & terminalÂ
#1 (E158) No. 23 - (E5) No. 1:
#2 (E158) No. 8 - (E16) No. 1:
#3 (E158) No. 9 - (E6) No. 1:
#4 (E158) No. 22 - (E17) No. 1:
Is the resistance less than 1 Ω?
YesÂ
Go to  4 .
NoÂ
Repair the open circuit of the harness between the ECM connector and fuel injector connector.
- CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTORÂ
.
Measure the resistance between ECM connector and chassis ground.
Connector & terminalÂ
#1 (E158) No. 23 - Chassis ground:
#2 (E158) No. 8 - Chassis ground:
#3 (E158) No. 9 - Chassis ground:
#4 (E158) No. 22 - Chassis ground:
Is the resistance 1 MΩ or more?
YesÂ
Go to  5 .
NoÂ
Repair the short circuit to ground in harness between ECM connector and fuel injector connector.
- CHECK EACH FUEL INJECTORÂ
.
Check each fuel injector. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>FUEL INJECTOR>INSPECTION .
Is the check result OK?
YesÂ
Go to  6 .
NoÂ
Replace the faulty fuel injector. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>FUEL INJECTOR .
- CHECK FOR POOR CONTACTÂ
.
Check for poor contact of ECM connector.
Is there poor contact of ECM connector?
YesÂ
Repair the poor contact of ECM connector.
NoÂ
Inspection using "General Diagnostic Table". Ref. to ENGINE (DIAGNOSTICS) (H4DO)>GENERAL DIAGNOSTIC TABLE>INSPECTION .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
