Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2018 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE
Drive Cycle B
| DTC | Item | Condition |
|---|---|---|
| P0087 | FUEL RAIL/SYSTEM PRESSURE - TOO LOW BANK 1 | Complete diagnosis with drive cycle A as well. |
| P0088 | FUEL RAIL/SYSTEM PRESSURE - TOO HIGH BANK 1 | Complete diagnosis with drive cycle A as well. |
| P0125 | INSUFFICIENT COOLANT TEMPERATURE FOR CLOSED LOOP FUEL CONTROL | «Coolant Temp.» at engine start: Less than -15°C (5°F) |
| P0130 | A/F/O2 SENSOR CIRCUIT BANK 1 SENSOR 1 | - |
| P0137 | O2 SENSOR CIRCUIT LOW VOLTAGE BANK 1 SENSOR 2 | - |
| P0138 | O2 SENSOR CIRCUIT HIGH VOLTAGE BANK 1 SENSOR 2 | - |
| P0171 | SYSTEM TOO LEAN BANK 1 | Complete diagnosis with drive cycle A as well. |
| P0172 | SYSTEM TOO RICH BANK 1 | Complete diagnosis with drive cycle A as well. |
| P0300 | RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED | Complete diagnosis with drive cycle A as well. |
| P0301 | CYLINDER 1 MISFIRE DETECTED | Complete diagnosis with drive cycle A as well. |
| P0302 | CYLINDER 2 MISFIRE DETECTED | Complete diagnosis with drive cycle A as well. |
| P0303 | CYLINDER 3 MISFIRE DETECTED | Complete diagnosis with drive cycle A as well. |
| P0304 | CYLINDER 4 MISFIRE DETECTED | Complete diagnosis with drive cycle A as well. |
| P0500 | VEHICLE SPEED SENSOR "A" CIRCUIT | - |
| P0506 | IDLE CONTROL SYSTEM RPM - LOWER THAN EXPECTED | - |
| P0507 | IDLE CONTROL SYSTEM RPM - HIGHER THAN EXPECTED | - |
| P062D | FUEL INJECTOR DRIVER CIRCUIT PERFORMANCE BANK 1 | - |
| P0700 | TRANSMISSION CONTROL SYSTEM (MIL REQUEST) | - |
| P0851 | PARK/NEUTRAL SWITCH INPUT CIRCUIT LOW | CVT model |
| P0852 | PARK/NEUTRAL SWITCH INPUT CIRCUIT HIGH | CVT model |
| P1191 | FUEL RAIL PRESSURE SENSOR "A" CIRCUIT NO ACTIVITY DETECTED | Complete diagnosis with drive cycle A as well. |
| P1261 | CYLINDER 1 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - |
| P1262 | CYLINDER 2 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - |
| P1263 | CYLINDER 3 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - |
| P1264 | CYLINDER 4 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - |
| P2096 | POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1 | Complete diagnosis with drive cycle A as well. |
| P2097 | POST CATALYST FUEL TRIM SYSTEM TOO RICH BANK 1 | Complete diagnosis with drive cycle A as well. |
Diagnostic procedure:Â
- Drive at 10 km/h (6 MPH) or more.
- Stop the vehicle and idle for ten minutes.
- Read the temporary code using the Subaru Select Monitor or general scan tool. Ref. to ENGINE (DIAGNOSTICS) (EXCEPT FOR STI)>Read Diagnostic Trouble Code (DTC)>OPERATIONÂ .
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.