2016 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE

Tech Tips April 2018 (TIPS 0218)

Publication date: 2018-04-01
Reference number: TIPS 0218

TECH TIPS APRIL 2018

TECH TIPS APRIL 2018

TECHNICAL SERVICE BULLETIN

Reference Number(s): TIPS 0218, Date of Issue:  April 01, 2018
SUBARU: 2014-2018 Forester; 2014 Impreza, Crosstrek; 2014-2016 Crosstrek Hybrid

01 QMR OF THE MONTH

We are pleased to announce February 2018 QMR of the Month winner:

A detailed QMR outlining his diagnosis and repair of DTC U0284 for Lost Communication with Active Grille Shutter (AGS) Module "A". While following the Service Manual troubleshooting steps, he confirmed the only current DTC was U0284 in the ECM. Then tested for a short to ground between the AGS connector and chassis ground. His DVOM results showed OL confirming there was no short. While measuring resistance in the wiring harness between the AGS connector and the ECM to check for an open circuit, his results showed 100k ohms. He began a closer inspection of the wiring harness, starting at the AGS connector. He started pulling back the wiring loom and found one section roughly an inch from the AGS connecter where the harness was wrapped with electrical tape. After removing the tape, he identified damaged insulation on wire A55 which exposed the copper wire conductor and allowed corrosion to accumulate. He performed a proper wire to wire harness repair and when completed, confirmed the resistance had returned to within specifications. After reassembly, clearing the DTC and thorough road testing, the DTC did not reset confirming the successful repair.

01 ICY ROAD WARNING INDICATOR OPERATION

The following TIPS article is applicable to the following models:

  • 2014-2018MY Forester 
  • 2014MY Impreza 
  • 2014MY Crosstrek 
  • 2014-2016MY Crosstrek Hybrid 
G11963293

The information should help clarify proper operation of the Icy Road indicator which illuminates in the combination meter when, based on input from the ambient temperature sensor, icy road surface conditions may exist.

The Owner's Manual provides the following information:

NOTE:
  • The outside temperature indicator shows the temperature around the sensor. Therefore, the temperature indication may differ from the actual outside air temperature.
  • The icy road surface warning screen should be treated only as a guide. Be sure to check the condition of the road surface before driving.
  • Once the icy road surface warning screen is displayed, it will not be displayed again unless the ignition switch is turned to the "ACC" or "ON" position after it has been turned to "LOCK"/"OFF" position. 

The italicized (third) bullet point above is incorrect and will be updated in future editions of the Owner's Manual. The new bullet point below explains proper warning indicator operation:

  • Once the icy road surface warning screen is displayed, it will not be displayed again unless the outside temperature has increased to 41°F (58°C) or higher then drops back to 37° (3°C) or below. 

15 2017MY+ IMPREZA/CROSSTREK (TURN START) REMOTE ENGINE START REGISTRATION

Vehicles & Remote Engine Start Kits Affected: 

  • 2017-2018MY+ Impreza/Crosstrek with Turn Start Ignition - H001SFL100/H001SFL101
  • 2019MY+ Impreza/Crosstrek with Turn Start Ignition - H001SFL400 (Coming soon)

Issue/Scenario:  The Technician may have a Control Module (ECU) that will not Register to the vehicle during the Remote Engine Start Installation process.

G11963294

Solution:  Confirm the Diagnostic Interface Tool (SSM IV) has the latest software (12.1.1 from January 2018 is the latest). Ensure all the steps for the Registration process are followed, per the installation instructions found on STIS and the steps are completed in less than 2 minutes  once the vehicle ignition has been turned ON to begin the process.

15 REMOTE START QUICK REFERENCE

The Techline continues to receive calls about RES run time adjustment. If you need to change the run time, please follow the instructions on the REMOTE START QUICK REFERENCE card. The card should be placed in the glove box per the installation instructions.

G11963295
NOTE: All vehicle doors, hood, trunk or rear gate must be closed prior to activating the remote engine start system. Any open entry point will prevent starting or cause the system to shut down.

Upon successful activation, the remote start transmitter will flash and beep one (1) time**, the horn will honk one (1) time and the side marker lights, tail lights and parking lights will flash one (1) time. The system will check certain safety preconditions before starting and if all conditions are met, the engine will start within five (5) seconds. After the engine starts, the remote start transmitter will flash and beep two (2) times**, the horn will honk one (1) time and the side marker lights, tail lights and parking lights will flash one (1) time. While the engine is running via the remote engine start system, the remote start transmitter will continue to flash one (1) time every three (3) seconds, the side marker lights, tail lights and parking lights will remain illuminated and the power window switches will be disabled. The engine will continue to run for fifteen (15) minutes unless one of the safety parameters below is triggered. The system also has a timer that will allow the system to operate for a maximum of twenty (20) minutes (under multiple remote start activations). Using the factory keyless entry transmitter (Access Key) to turn on the ignition resets the twenty (20) minute timer.

If the engine turns over but does not start (or starts and stalls) the remote engine start system will shut down and then attempt to start the engine three (3) additional times. The system will not attempt to restart the engine if it determines a vehicle malfunction is preventing it from starting. If the engine does not start after the three (3) additional attempts, the remote engine start request will be aborted.

Remote Engine Start Safety Parameters 

For safety and security reasons, the system will fail to start or shut down the engine during remote start operation if any of the following occur:

  • The remote start system has operated for twenty (20) minutes between ignition ON cycles

    The horn will honk three (3) times and the parking lights will flash three (3) times 

  • Any of the vehicle's doors, trunk or rear gate are open

    The horn will honk six (6) times and the parking lights will flash six (6) times 

  • The vehicle's hood is open 

    The horn will honk two (2) times and the parking lights will flash two (2) times

  • The transmission shifter is not in the "park" position 

    The horn will honk two (2) times and the parking lights will flash two (2) times 

  • The vehicle's brake pedal is pressed

    The horn will honk two (2) times and the parking lights will flash two (2) times 

  • The vehicle's engine idle speed has reached a level over 3,500 RPM (this will cause the engine to shutdown)
  • The vehicle's security system is triggered by opening a door or rear gate (if the security system is armed at the time of remote start activation)

In addition to the items above, if the vehicle's engine management system determines there is a safety risk due to a vehicle related problem, the engine will shut down.

WARNING: TO AVOID DANGER OF CARBON MONOXIDE, NEVER REMOTE START A VEHICLE IN A CLOSED SPACE SUCH AS A CLOSED GARAGE.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.