Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2015 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE
Inspection Mode E
WARNING: This page is about a different car, the 2022 Subaru WRX. However, it is still accessible from the selected car via links, so may be relevant.
| DTC | Description & trouble part | Condition |
|---|---|---|
| P0801 | REVERSE INHIBIT CONTROL CIRCUIT/OPEN | - |
| P0841 | TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT RANGE/PERFORMANCE | Perform inspection mode E three times |
| P0846 | TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "B" CIRCUIT RANGE/PERFORMANCE | Perform inspection mode E three times |
| U0073 | CONTROL MODULE COMMUNICATION BUS OFF | - |
| U0100 | LOST COMMUNICATION WITH ECM/PCM "A" | - |
| U0122 | LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE | - |
| U0128 | LOST COMMUNICATION WITH PARK BRAKE CONTROL MODULE | - |
| U0131 | LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE | - |
| U0140 | LOST COMMUNICATION WITH BODY CONTROL MODULE | - |
| U0155 | LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULE | - |
| U0162 | LOST COMMUNICATION WITH AUDIO VISUAL NAVIGATION DISPLAY MODULE | - |
| U0164 | LOST COMMUNICATION WITH HVAC CONTROL MODULE | - |
| U0401 | INVALID DATA RECEIVED FROM ECM/PCM "A" | - |
| U0416 | INVALID DATA RECEIVED FROM VEHICLE DYNAMICS CONTROL MODULE | - |
| U0417 | INVALID DATA RECEIVED FROM PARK BRAKE CONTROL MODULE | - |
| U0420 | INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE | - |
| U0422 | INVALID DATA RECEIVED FROM BODY CONTROL MODULE | - |
| U0423 | INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL MODULE | - |
| U0424 | INVALID DATA RECEIVED FROM HVAC CONTROL MODULE | - |
| U0463 | INVALID DATA RECEIVED FROM NAVIGATION DISPLAY MODULE | - |
| U1235 | LOST COMMUNICATION WITH EyeSight | - |
| U1433 | INVALID DATA RECEIVED FROM EyeSight | - |
| U1C00 | INVALID AUTHENTICATION DATA RECEIVED FROM GATEWAY | - |
| U1C07 | INVALID AUTHENTICATION DATA RECEIVED FROM ECM/PCM PU-BUS | - |
| U1C08 | INVALID AUTHENTICATION DATA RECEIVED FROM VDC PU-BUS | - |
| U1D00 | CONTINUINGLY INVALID AUTHENTICATION DATA RECEIVED FROM GATEWAY | - |
| U1D07 | CONTINUINGLY INVALID AUTHENTICATION DATA RECEIVED FROM ECM/PCM PU-BUS | - |
| U1D08 | INVALID AUTHENTICATION DATA RECEIVED FROM VDC PU-BUS | - |
| U1E00 | LOST COMMUNICATION OF AUTHENTICATION DATA WITH GATEWAY "A" PU-BUS | - |
| U1E07 | LOST COMMUNICATION OF AUTHENTICATION DATA WITH ECM/PCM PU-BUS | - |
| U1E08 | LOST COMMUNICATION OF AUTHENTICATION DATA WITH VDC PU-BUS | - |
Diagnostic procedure:
- Check the readiness code of [Transmission] using Subaru Select Monitor and confirm that the diagnosis is not completed. Ref. to TRANSMISSION (DIAGNOSTICS)>ALL READINESS DIAGNOSTIC CODE(S)
- Start the engine.
- Check the readiness code of [Transmission] using Subaru Select Monitor and confirm that the diagnosis is completed. Ref. to TRANSMISSION (DIAGNOSTICS)>ALL READINESS DIAGNOSTIC CODE(S)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.