Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2015 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE
Inspection Mode C
WARNING: This page is about a different car, the 2022 Subaru WRX. However, it is still accessible from the selected car via links, so may be relevant.
| DTC | Description & trouble part | Condition |
|---|---|---|
| P0500 | VEHICLE SPEED SENSOR "A" CIRCUIT | - |
| P0720 | OUTPUT SHAFT SPEED SENSOR CIRCUIT | - |
| P0721 | OUTPUT SHAFT SPEED SENSOR CIRCUIT RANGE/PERFORMANCE | - |
| P0961 | PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT RANGE/PERFORMANCE | - |
| P0965 | PRESSURE CONTROL SOLENOID "B" CONTROL CIRCUIT RANGE/PERFORMANCE | - |
| P0970 | PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT LOW | - |
| P0971 | PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT HIGH | - |
| P0973 | SHIFT SOLENOID "A" CONTROL CIRCUIT LOW | - |
| P0974 | SHIFT SOLENOID "A" CONTROL CIRCUIT HIGH | - |
| P0976 | SHIFT SOLENOID "B" CONTROL CIRCUIT LOW | - |
| P0977 | SHIFT SOLENOID "B" CONTROL CIRCUIT HIGH | - |
| P1706 | REAR OUTPUT SHAFT SPEED SENSOR CIRCUIT NO SIGNAL | - |
| P170B | REAR OUTPUT SHAFT SPEED SENSOR CIRCUIT RANGE/PERFORMANCE | - |
| P2158 | VEHICLE SPEED SENSOR "B" CIRCUIT | - |
| P2728 | PRESSURE CONTROL SOLENOID "E" CONTROL CIRCUIT RANGE/PERFORMANCE | - |
| P2746 | INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT RANGE/PERFORMANCE | - |
| P2747 | INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT NO SIGNAL | - |
| P2750 | INTERMEDIATE SHAFT SPEED SENSOR "C" CIRCUIT RANGE/PERFORMANCE | - |
| P2751 | INTERMEDIATE SHAFT SPEED SENSOR "C" CIRCUIT NO SIGNAL | - |
| P2763 | TORQUE CONVERTER CLUTCH PRESSURE CONTROL SOLENOID CONTROL CIRCUIT HIGH | - |
| P2764 | TORQUE CONVERTER CLUTCH PRESSURE CONTROL SOLENOID CONTROL CIRCUIT LOW | - |
Diagnostic procedure:
- Start the engine.
- Check the readiness code of [Transmission] using Subaru Select Monitor and confirm that the diagnosis is not completed. Ref. to TRANSMISSION (DIAGNOSTICS)>ALL READINESS DIAGNOSTIC CODE(S)
- Shift the select lever to "D" range and wait for 10 seconds.
- Accelerate slowly to a legal speed, and then decelerate slowly to a stop.
- Check the readiness code of [Transmission] using Subaru Select Monitor and confirm that the diagnosis is completed. Ref. to TRANSMISSION (DIAGNOSTICS)>ALL READINESS DIAGNOSTIC CODE(S)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.