2015 Subaru WRX BaseFACTORY OEM SERVICE PROCEDURE

Module I/O Signal

WARNING: This page is about a different car, the 2016 Subaru Outback and 2016 Subaru Legacy. However, it is still accessible from the selected car via links, so may be relevant.

Model with 6.2 inch display 

Fig 1: Audio System Module I/O Signal Connector Terminal Identification
G10309127Courtesy of SUBARU OF AMERICA, INC.
  • Power supply and speaker output terminal
    Terminal No. Content Measuring condition Measurement value Note
    (i85) No. 1 FRONT-RH (+) - - -
    (i85) No. 2 FRONT-LH (+) - - -
    (i85) No. 3 ←→ Chassis ground ACC ACC ON 11 - 15 V -
    (i85) No. 4 ←→ Chassis ground +B Always 11 - 15 V -
    (i85) No. 5 FRONT-RH (-) - - -
    (i85) No. 6 FRONT-LH (-) - - -
    (i85) No. 7 ←→ Chassis ground GND Always 0 V -
    (i85) No. 8 ANTENNA-ON - - -
    (i85) No. 9 N.C. - - -
    (i85) No. 10 ILLUMI (+) - - -
    (i131) No. 1 REAR-RH (+) - - -
    (i131) No. 2 REAR-LH (+) - - -
    (i131) No. 3 REAR-RH (-) - - -
    (i131) No. 4 N.C. - - -
    (i131) No. 5 ILLUMI (-) - - -
    (i131) No. 6 REAR-LH (-) - - -
  • Steering switch and AUX input terminal for microphone etc.
    Terminal No. Content Measuring condition Measurement value Note
    (i192) No. 1 URAT - - -
    (i192) No. 2 REV - - -
    (i192) No. 3 BRIGHT - - -
    (i192) No. 4 MAC +B - - -
    (i192) No. 5 MIC (+) - - -
    (i192) No. 6 MIC-DET - - -
    (i192) No. 7 N.C. - - -
    (i192) No. 8 N.C. - - -
    (i192) No. 9 N.C. - - -
    (i192) No. 10 N.C. - - -
    (i192) No. 11 CAM + 6V - - -
    (i192) No. 12 CV (+) - - -
    (i192) No. 13 CV (-) (SHIELD) - - -
    (i192) No. 14 SHIELD-GND (AUX) - - -
    (i192) No. 15 ←→ Chassis ground PKB At parking ON 1 V or less -
    (i192) No. 16 N.C. - - -
    (i192) No. 17 ←→ Chassis ground SPD When the tire is rotating Pulse signal -
    (i192) No. 18 SHIELD-GND (MIC) - - -
    (i192) No. 19 MIC (-) - - -
    (i192) No. 20 GND (CAMERA) - - -
    (i192) No. 21 SW1 (+) - - -
    (i192) No. 22 SW2 (+) - - -
    (i192) No. 23 SW-GND - - -
    (i192) No. 24 N.C. - - -
    (i192) No. 25 AUX-ON - - -
    (i192) No. 26 AUX-R (+) - - -
    (i192) No. 27 AUX-LR (-) - - -
    (i192) No. 28 AUX-L (+) - - -

    Model with 7 inch display 

    Refer to "Control Module I/O Signal" of "INFOTAINMENT SYSTEM (DIAGNOSTICS)". < Ref. to ELECTRICAL SPECIFICATION , Control Module I/O Signal. >

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.