2014 Subaru TribecaFACTORY OEM SERVICE PROCEDURE

Shift Lock Operation

Step Check Yes No
1 CHECK COMMUNICATION OF SUBARU SELECT MONITOR. 
  1. Turn the ignition switch to ON.
  2. Using the Subaru Select Monitor, check whether communication to all systems can be executed normally.
 Is the system name displayed? Go to step 2  . Perform the inspection following the diagnostic procedure in the LAN section. < Ref. to BASIC DIAGNOSTIC PROCEDURE . >
2 CHECK SHIFT LOCK. 
  1. Turn the ignition switch to ON.
  2. Shift the select lever to "P" range.
 While brake pedal is not depressed, is it possible to move the select lever from the "P" range to other ranges? Perform the inspection of "SELECT LEVER CANNOT BE LOCKED OR RELEASED". < Ref. to SELECT LEVER CANNOT BE LOCKED OR RELEASED , INSPECTION, AT Shift Lock Control System. > Go to step 3  .
3 CHECK SHIFT LOCK.  While brake pedal is depressed, is it possible to move the select lever from the "P" range to other ranges? Go to step 4  . Perform the inspection of "SELECT LEVER CANNOT BE LOCKED OR RELEASED". < Ref. to SELECT LEVER CANNOT BE LOCKED OR RELEASED , INSPECTION, AT Shift Lock Control System. >
4 CHECK SHIFT LOCK. 
Shift the select lever to "N" range.		 Is it possible to move the select lever from the "N" range to the "P" range? Go to step 5  . Perform the inspection of "SELECT LEVER CANNOT BE LOCKED OR RELEASED". < Ref. to SELECT LEVER CANNOT BE LOCKED OR RELEASED , INSPECTION, AT Shift Lock Control System. >
5 CHECK SHIFT LOCK. 
  1. Shift the select lever to "N" range.
  2. Turn the ignition switch to ACC.
 While brake pedal is depressed, is it possible to move the select lever from the "N" range to the "P" range? Go to step 6  . Perform the inspection of "SELECT LEVER CANNOT BE LOCKED OR RELEASED". < Ref. to SELECT LEVER CANNOT BE LOCKED OR RELEASED , INSPECTION, AT Shift Lock Control System. >
6 CHECK KEY INTERLOCK. 
  1. Turn the ignition switch to OFF.
  2. Shift the select lever to other than "P" range.
 Can the ignition key be removed? Perform the inspection of "KEY INTERLOCK CANNOT BE LOCKED OR RELEASED". < Ref. to KEY INTERLOCK DOES NOT LOCK OR RELEASE , INSPECTION, AT Shift Lock Control System. > Go to step 7  .
7 CHECK KEY INTERLOCK. 
Shift the select lever to "P" range.		 Can the ignition key be removed? AT shift lock system is normal. Perform the inspection of "KEY INTERLOCK CANNOT BE LOCKED OR RELEASED". < Ref. to KEY INTERLOCK DOES NOT LOCK OR RELEASE , INSPECTION, AT Shift Lock Control System. >
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.