Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Mode $01 (Current Powertrain Diagnostic Data)
Refer to data denoting the current operating condition of analog input/output, digital input/output or the powertrain system.
A list of the support data and PID (Parameter Identification) codes are shown in the following table.
| PID | Data | Unit of measure |
|---|---|---|
| $01 | Number of emission-related powertrain DTC and malfunction indicator light status | - |
| $03 | Fuel system control status | - |
| $04 | Calculated engine load value | % |
| $05 | Engine coolant temperature | °C |
| $06 | Short term fuel trim (Bank 1) | % |
| $07 | Long term fuel trim (Bank 1) | % |
| $08 | Short term fuel trim (Bank 2) | % |
| $09 | Long term fuel trim (Bank 2) | % |
| $0B | Intake manifold absolute pressure | kPa |
| $0C | Engine speed | rpm |
| $0D | Vehicle speed | MPH |
| $0E | Ignition timing advance | ° |
| $0F | Intake air temperature | °C |
| $10 | Intake air amount | g/s |
| $11 | Throttle valve opening angle | % |
| $13 | Air fuel ratio sensor | - |
| $15 | Oxygen sensor output voltage (Bank 1 Sensor 2) | V |
| $15 | Oxygen sensor correction (Bank 1 Sensor 2) | % |
| $19 | Oxygen sensor output voltage (Bank 2 Sensor 2) | V |
| $19 | Oxygen sensor correction (Bank 2 Sensor 2) | % |
| $1C | On-board diagnostic system | - |
| $1F | Elapsed time after starting the engine | sec |
| $21 | Travel distance after the malfunction indicator light illuminates | miles |
| $24 | Oxygen sensor output voltage and short term fuel trim associated with oxygen sensor (Bank 1) | - and V |
| $28 | Oxygen sensor output voltage and short term fuel trim associated with oxygen sensor (Bank 2) | - and V |
| $2C | Target EGR | % |
| $2D | EGR deviation | % |
| $2E | Evaporative purge | % |
| $2F | Fuel level | % |
| $30 | Number of warm ups after DTC clear | - |
| $31 | Travel distance after DTC clear | miles |
| $33 | Barometric pressure | kPa |
| $34 | A/F sensor lambda value (Bank 1 Sensor 1) | - |
| $34 | A/F sensor current value (Bank 1 Sensor 1) | mA |
| $38 | A/F sensor lambda value (Bank 2 Sensor 1) | - |
| $38 | A/F sensor current value (Bank 2 Sensor 1) | mA |
| $3C | Catalyst temperature #1 | °C |
| $3D | Catalyst temperature #2 | °C |
| $41 | Diagnostic monitor of each drive cycle | - |
| $42 | ECM power voltage | V |
| $43 | Absolute load | % |
| $44 | A/F target lambda | - |
| $45 | Relative throttle opening angle | % |
| $46 | Ambient temperature | °C |
| $47 | Absolute throttle opening angle 2 | % |
| $49 | Absolute accelerator opening angle 1 | % |
| $4A | Absolute accelerator opening angle 2 | % |
| $4C | Target throttle opening angle | % |
| $4D | Engine operating time while malfunction indicator light lit | min |
| $4E | Elapsed time after DTC clear | min |
| $51 | Fuel used | - |
| $5A | Relative accelerator opening angle | % |
| $65 | Neutral status | - |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.