Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2013 Subaru TribecaFACTORY OEM SERVICE PROCEDURE
Drive Cycle C
| DTC | Item | Condition |
|---|---|---|
| *P0030 | HO2S Heater Control Circuit (Bank 1 Sensor 1) | - |
| *P0050 | HO2S Heater Control Circuit (Bank 2 Sensor 1) | - |
| *P0068 | MAP/MAF - Throttle Position Correlation | - |
| *P0101 | Mass or Volume Air Flow Circuit Range/Performance | - |
| P0134 | O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1) | - |
| *P013A | O2 Sensor Slow Response - Rich to Lean (Bank 1 Sensor 2) | - |
| *P013B | O2 Sensor Slow Response - Lean to Rich (Bank 1 Sensor 2) | - |
| *P013C | O2 Sensor Slow Response - Rich to Lean (Bank 2 Sensor 2) | - |
| *P013D | O2 Sensor Slow Response - Lean to Rich (Bank 2 Sensor 2) | - |
| *P013E | O2 Sensor Delayed Response - Rich to Lean (Bank 1 Sensor 2) | - |
| *P013F | O2 Sensor Delayed Response - Lean to Rich (Bank 1 Sensor 2) | - |
| *P014A | O2 Sensor Delayed Response - Rich to Lean (Bank 2 Sensor 2) | - |
| *P014B | O2 Sensor Delayed Response - Lean to Rich (Bank 2 Sensor 2) | - |
| P0154 | O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 1) | - |
| *P0171 | System Too Lean (Bank 1) | Complete diagnosis with drive cycle A or B as well. |
| *P0172 | System Too Rich (Bank 1) | Complete diagnosis with drive cycle A or B as well. |
| *P0174 | System Too Lean (Bank 2) | Complete diagnosis with drive cycle A or B as well. |
| *P0175 | System Too Rich (Bank 2) | Complete diagnosis with drive cycle A or B as well. |
| *P0300 | Random/Multiple Cylinder Misfire Detected | Complete diagnosis with drive cycle A or B as well. |
| *P0301 | Cylinder 1 Misfire Detected | Complete diagnosis with drive cycle A or B as well. |
| *P0302 | Cylinder 2 Misfire Detected | Complete diagnosis with drive cycle A or B as well. |
| *P0303 | Cylinder 3 Misfire Detected | Complete diagnosis with drive cycle A or B as well. |
| *P0304 | Cylinder 4 Misfire Detected | Complete diagnosis with drive cycle A or B as well. |
| *P0305 | Cylinder 5 Misfire Detected | Complete diagnosis with drive cycle A or B as well. |
| *P0306 | Cylinder 6 Misfire Detected | Complete diagnosis with drive cycle A or B as well. |
| *P0400 | Exhaust Gas Recirculation Flow | - |
| *P0441 | Evaporative Emission Cont. Sys. Incorrect Purge Flow | - |
| *P1449 | Evaporative Emission Cont. Sys. Air Filter Clog | - |
| P1492 | EGR Solenoid Valve Signal #1 Circuit Malfunction (Low Input) | - |
| P1493 | EGR Solenoid Valve Signal #1 Circuit Malfunction (High Input) | - |
| P1494 | EGR Solenoid Valve Signal #2 Circuit Malfunction (Low Input) | - |
| P1495 | EGR Solenoid Valve Signal #2 Circuit Malfunction (High Input) | - |
| P1496 | EGR Solenoid Valve Signal #3 Circuit Malfunction (Low Input) | - |
| P1497 | EGR Solenoid Valve Signal #3 Circuit Malfunction (High Input) | - |
| P1498 | EGR Solenoid Valve Signal #4 Circuit Malfunction (Low Input) | - |
| P1499 | EGR Solenoid Valve Signal #4 Circuit Malfunction (High Input) | - |
| *P2096 | Post Catalyst Fuel Trim System Too Lean (Bank 1) | Complete diagnosis with drive cycle A or B as well. |
| *P2097 | Post Catalyst Fuel Trim System Too Rich (Bank 1) | Complete diagnosis with drive cycle A or B as well. |
| *P2098 | Post Catalyst Fuel Trim System Too Lean Bank 2 | Complete diagnosis with drive cycle A or B as well. |
| *P2099 | Post Catalyst Fuel Trim System Too Rich Bank 2 | Complete diagnosis with drive cycle A or B as well. |
| *P219A | Bank 1 Air-Fuel Ratio Imbalance | Complete diagnosis with drive cycle B as well. |
| *P219B | Bank 2 Air-Fuel Ratio Imbalance | Complete diagnosis with drive cycle B as well. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.