2013 Subaru Forester X, Standard TransFACTORY OEM SERVICE PROCEDURE

Turbo Model

Option code(1) UI MD 62 MF NB MD MT
Engine type 2.5 L turbo
Grade XT XT LIMITED XT LIMITED Plus
Transmission 4AT
Vehicle weight (C.W.) Front axle kg (lb) 855 (1, 885) 860 (1, 895) 860 (1, 895) 860 (1, 895) 860 (1, 895) 860 (1, 895) 860 (1, 895)
Rear axle kg (lb) 710 (1, 565) 710 (1, 565) 710 (1, 565) 710 (1, 565) 710 (1, 565) 710 (1, 565) 710 (1, 565)
Total kg (lb) 1, 565 (3, 450) 1, 570 (3, 460) 1, 570 (3, 460) 1, 570 (3, 460) 1, 570 (3, 460) 1, 570 (3, 460) 1, 570 (3, 460)
Total axle weight (G.A.W.) Front axle kg (lb) 1, 050 (2, 310) 1, 050 (2, 310) 1, 050 (2, 310) 1, 050 (2, 310) 1, 050 (2, 310) 1, 050 (2, 310) 1, 050 (2, 310)
Rear axle kg (lb) 1, 095 (2, 410) 1, 095 (2, 410) 1, 095 (2, 410) 1, 095 (2, 410) 1, 095 (2, 410) 1, 095 (2, 410) 1, 095 (2, 410)
Gross vehicle weight (G.V.W.) kg (lb) 2, 055 (4, 525) 2, 055 (4, 525) 2, 055 (4, 525) 2, 055 (4, 525) 2, 055 (4, 525) 2, 055 (4, 525) 2, 055 (4, 525)
Option Aluminum wheel (16-inch) - - - - - - -
Aluminum wheel (17-inch) ◦ ◦ ◦ ◦ ◦ ◦ ◦
Leather seats and leather door trim center decoration - ◦ ◦ ◦ ◦ ◦ ◦
Power seat ◦ ◦ ◦ ◦ ◦ ◦ ◦
Cruise control ◦ ◦ ◦ ◦ ◦ ◦ ◦
Front fog light - ◦ ◦ ◦ ◦ ◦ ◦
HID headlight - ◦ ◦ ◦ - ◦ ◦
Dark colored glass ◦ ◦ ◦ ◦ ◦ ◦ ◦
Sunroof ◦ ◦ ◦ ◦ ◦ ◦ ◦
High grade audio - - - - ◦ - -
High grade audio display - - - - - - ◦
Navigation system - ◦ - - - ◦ -
Seat heater - ◦ ◦ ◦ ◦ ◦ ◦
Front wiper deicer - ◦ ◦ ◦ ◦ ◦ ◦
Heated mirror - ◦ ◦ ◦ ◦ ◦ ◦
Side airbag ◦ ◦ ◦ ◦ ◦ ◦ ◦
Curtain airbag ◦ ◦ ◦ ◦ ◦ ◦ ◦
Special edition - - ◦ - - - -
(1) For option codes, refer to the ID information. < Refer to MODEL NUMBER LABEL , IDENTIFICATION, Identification. >
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.