2012 Subaru Outback Base, Standard TransFACTORY OEM SERVICE PROCEDURE

Check Door Lock Switch

Step Check Yes No
1 CHECK DOOR LOCK SWITCH. 
  1. Prepare the Subaru Select Monitor kit.
  2. Turn the ignition switch to ON (engine OFF) and run the "PC application for Subaru Select Monitor".
  3. On << System Selection Menu >> display, select {Integ. unit mode}.
  4. Select the {Current Data Display & Save}.
  5. Select the {Manual lock SW input}.
Does the display switch between OFF ↔ ON when each door lock switch is moved to LOCK? Go to step 2.  Go to step 3  .
2 CHECK DOOR LOCK SWITCH. 
From the condition in step 1), operate each door lock switch (driver's and passenger's) in the UNLOCK direction.
Does the display switch between OFF ↔ ON? The door lock switch is OK. Go to step 4  .
3 CHECK DOOR LOCK SWITCH. 
  1. Disconnect the door lock switch connector.
  2. Check the continuity when the door lock switch is operated to the LOCK direction.

    Connector & terminal 

    Driver's side (model without AUTO UP function) 

    (D7) No. 2 - (D7) No. 3: 

    Driver's side (model with AUTO UP function) 

    (D95) No. 10 - (D7) No. 3: 

    Passenger's side 

    (D125) No. 4 - (D125) No. 5: 

Did the indicator change from "No continuity" (1 MΩ or more) to "Continuity exists" (less than 10 Ω)? Go to step 4.  Replace the power window main switch or door lock switch.
4 CHECK DOOR LOCK SWITCH. 
Check the continuity when the door lock switch is operated to the UNLOCK direction.
Connector & terminal 
Driver's side (model without AUTO UP function) 
(D7) No. 1 - (D7) No. 3: 
Driver's side (model with AUTO UP function) 
(D95) No. 2 - (D7) No. 3: 
Passenger's side 
(D125) No. 2 - (D125) No. 5: 
Did the indicator change from "No continuity" (1 MΩ or more) to "Continuity exists" (less than 10 Ω)? Go to step 5.  Replace the power window main switch or door lock switch.
5 CHECK HARNESS. 
Measure the resistance between the door lock switch connector and chassis ground.
Connector & terminal 
Driver's side 
(D7) No. 3 - Chassis ground: 
Passenger's side 
(D125) No. 5 - Chassis ground: 
Is the resistance less than 10 Ω? Go to step 6.  Repair or replace the harness.
6 CHECK HARNESS. 
  1. Disconnect the body integrated unit connector.
  2. Measure the resistance between body integrated unit connector and door lock switch connector.

    Connector & terminal 

    Driver's side (model without AUTO UP function) 

    (D7) No. 2 - (i84) No. 9: 

    (D7) No. 1 - (i84) No. 20: 

    Driver's side (model with AUTO UP function) 

    (D95) No. 10 - (i84) No. 9: 

    (D95) No. 2 - (i84) No. 20: 

    Passenger's side 

    (D125) No. 4 - (i84) No. 9: 

    (D125) No. 2 - (i84) No. 20: 

Is the resistance less than 10 Ω? Replace the body integrated unit. Refer to , BODY INTEGRATED UNIT . Repair or replace the harness.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.