2012 Subaru Outback Base, Standard TransFACTORY OEM SERVICE PROCEDURE

Check Keyless Buzzer

Step Check Yes No
1 CHECK KEYLESS BUZZER SETTING. 
  1. Prepare the Subaru Select Monitor kit.
  2. Turn the ignition switch to ON (engine OFF) and run the "PC application for Subaru Select Monitor".
  3. On << System Selection Menu >> display, select {Integ. unit mode}.
  4. Select {Answer-back buzzer setup} from {Integ. Unit customizing}.
 Is the setting ON? Go to step 2.  Turn the setting to ON.
2 CHECK BODY INTEGRATED UNIT. 
  1. Select the {Function check} from {Integ. unit mode}.
  2. Select the {Keyless Buzzer Output} and execute it.
 Does the keyless buzzer sound? Check the keyless control module. Go to step 3  .
3 CHECK KEYLESS BUZZER CIRCUIT. 
  1. Turn the ignition switch to OFF.
  2. Disconnect the body integrated unit connector and keyless buzzer connector.
  3. Measure the resistance between body integrated unit connector and keyless buzzer connector.

    Connector & terminal 

    (B280) No. 20 - (B490) No. 1: 

 Is the resistance less than 10 Ω? Go to step 4.  Repair or replace the harness.
4 CHECK KEYLESS BUZZER CIRCUIT. 
Measure the resistance between keyless buzzer connector and chassis ground.
Connector & terminal 
(B490) No. 2 - Chassis ground: 		 Is the resistance less than 10 Ω? Go to step 5.  Repair or replace the harness.
5 CHECK KEYLESS BUZZER. 
  1. Remove the keyless buzzer.
  2. Connect the battery positive (+) terminal to terminal No. 1 of the keyless buzzer, and the negative (-) terminal to terminal No. 2, and check whether or not the buzzer will sound. Refer to , INSPECTION , Keyless Buzzer.
 Does the keyless buzzer sound? Go to step 6.  Replace the keyless buzzer.
6 CHECK BODY INTEGRATED UNIT. 
  1. Select the {Function check} from {Integ. unit mode}.
  2. Select the {Keyless Buzzer Output} and execute it.
  3. Measure the voltage between body integrated unit connector and chassis ground.
 Is the voltage 9 V or more? Go to step 7.  Replace the body integrated unit. Refer to , BODY INTEGRATED UNIT .
7 CHECK OUTPUT OF BODY INTEGRATED UNIT. 
  1. Select the {Current Data Display & Save} from {Integ. unit mode}.
  2. Select the {Keyless Buzzer Output}.
  3. Press the LOCK/UNLOCK button of the keyless transmitter.
 Is output signal present when operating the LOCK/UNLOCK button? System is normal. Inspect the keyless entry system. If there are no problems, replace the body integrated unit.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.